Read This First; Setting Up The Speaker Systems; Connections - Denon AVR-1602 Bedienungsanleitung

6 READ THIS FIRST

This A / V surround Receiver must be setup before use. Following these steps.
Step 1
(page 5 to 7)
Choose the location to setup the speakers and connecting the components.
Step 2
(page 8)
Next, insert the batteries into the remote control unit.
Step 3
(page 8 to 10)
Finally, setting up the system.

7 SETTING UP THE SPEAKER SYSTEMS

2 Speaker system layout
Basic system layout
• The following is an example of the basic layout for a system consisting of six speaker systems and a television
monitor:
Subwoofer
Front speaker systems
Set these at the sides of the TV or
screen with their front surfaces as
flush with the front of the screen as
possible.
Downloaded from www.Manualslib.com
Center speaker system
Surround speaker systems
manuals search engine

8 CONNECTIONS

• Do not plug in the power cord until all connections
have been completed.
• Be sure to connect the left and right channels
properly (left with left, right with right).
• Insert the plugs securely. Incomplete connections
will result in the generation of noise.
• Use the AC OUTLET for audio equipment only. Do
not use them for hair driers, etc.
Connecting the audio components
Decoders with 6-channel
analog outputs, etc.
LINE OUT
R L
AUDIO DIGITAL PRE OUT
R L IN IN
SUB
AM
CD
LOOP WOOFER
ANT.
DVD/ DVD/
VDP
VDP
FM
TV/ TV/
COAX.
DBS COAXIAL DBS
75
VCR VCR
ANTENNA TERMINALS
CDR/ OPTICAL
FR FL MONITOR
TAPE
SW C VCR VCR
CDR/
SR SL OPTICAL
TAPE
OUT OUT
EXT. IN VIDEO
R L R L
AUDIO IN
AUDIO OUT
Tape deck or CD recorder
R L R L
R L R L
INPUT OUTPUT
Connecting a tape deck
Connections for recording:
Connect the tape deck's recording input jacks (LINE IN
or REC) to this unit's tape recording (OUT) jacks using
pin plug cords.
Connections for playback:
Connect the tape deck's playback output jacks (LINE
OUT or PB) to this unit's tape playback (IN) jacks using
pin plug cords.
CD recorder, MD recorder or other component
equipped with digital input/output jacks
OPTICAL
B
OUTPUT INPUT
DIGITAL jacks
Use these for connections to audio equipment with digital output.
Refer to Page 10 for instructions on setting this terminal.
• Use 75 Ω/ohms cable pin cords (sold separately) for coaxial
connections.
• Use optical cables (sold separately) for optical connections.
• Note that binding pin plug cords together with power
cords or placing them near a power transformer
will result in generating hum or other noise.
• Noise or humming may be generated if a connected
audio equipment is used independently without
turning the power of this unit on. If this happens,
turn on the power of this unit.
AC OUTLET
IN
SPEAKER SYSTEMS
FRONT CENTER SURROUND
B A
R L R L
R L
AC 230V 50Hz
SWITCHED
100W MAX.
SPEAKER IMPEDANCE
OUT
FRONT A OR B / 6 16 CENTER / 6 16
A + B / 6 16 SURROUND / 6 16
Subwoofer jack
Connect the internal amplifier's subwoofer to the
subwoofer terminal. (Refer to page 7.)
Connecting the AC OUTLET
AC OUTLETS
• SWITCHED (capacity – 100 W)
The power to these outlets is turned on and off in conjunction
with the power operation switch on the main unit, and when the
power is switched between on and standby from the remote
control unit.
No power is supplied from these outlets when this unit's power is
at standby. Never connect equipment whose capacity is above
100 W.
NOTE:
Only use the AC OUTLET for audio equipment. Never use them
for hair driers, TVs or other electrical appliances.
CD player
OUTPUT
R L
DIGITAL AUDIO DIGITAL AUDIO
R L
Connecting a CD player
AUDIO OUT
Connect the CD player's analog output jacks (ANALOG
OUTPUT) to this unit's CD jacks using pin plug cords.
ENGLISH
AC CORD
AC 230 V, 50 Hz
5