Specifications - Makita BFT020F Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Battery cartridge
1-2. Button
2-1. Red part
2-2. Button
2-3. Battery cartridge
3-1. Switch trigger
4-1. Reversing switch lever
5-1. Front lamp

SPECIFICATIONS

Model
Fastening
torque
No load speed (min
Dimensions
Net weight
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model BFT020F, BFT021F, BFT040F, BFT042F,
BFT080F, BFT081F, BFT122F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB(A)
Model BFT123F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Downloaded from www.Manualslib.com
6-1. LED indicator
7-1. Adjusting ring
7-2. Ring
8-1. Adjusting ring
8-2. Ring
8-3. Scale
8-4. Adjusting grip
8-5. Hole for adjusting grip
BFT020F BFT021F
Hard joint 0.5 - 2 N•m 0.5 - 2 N•m
Soft joint 0.5 - 2 N•m 0.5 - 2 N•m
-1
) 540 320
(with Battery Cartridge BH9020/BH9020A)
(with Battery Cartridge BH9033/BH9033A)
) : 70 dB(A) or less
pA
) : 71 dB(A)
pA
Wear ear protection
manuals search engine
Explanation of general view
BFT040F BFT080F
1 - 4 N•m 3 - 8 N•m
1 - 3.5 N•m 3 - 6.5 N•m
950 540
200 x 65 x 251mm
200 x 65 x 274 mm
1.4 kg
D.C.9.6V
ENE033-1
Vibration
The vibration total value (tri-axial vector sum) determined
ENF002-1
according to EN60745:
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
ENG905-1
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
3
8-6. Yellow line
8-7. Compression spring
10-1. Bit
10-2. Sleeve
12-1. Limit mark
13-1. Brush holder cap
13-2. Screwdriver
BFT122F BFT042F BFT081F
5 - 12 N•m 1 - 4 N•m 3 - 8 N•m
5 - 10 N•m 1 - 3.5 N•m 3 - 7.5 N•m
320 1,200 700
200 x 71 x 242 mm
(with Battery Cartridge BH1220C)
200 x 71 x 251 mm
(with Battery Cartridge BH1233C)
1.5 kg
D.C.12V
2
) : 2.5 m/s or less
h
2
BFT123F
5 - 12 N•m
5 - 12 N•m
390
ENG900-1
ENG901-1