Specifications - Makita DA6301 Betriebsanleitung

ENGLISH
(Original instructions)
1 Counterclockwise
2 Switch trigger
3 Clockwise
4 Pin
5 Slide button

SPECIFICATIONS

Model
Capacities
Wood
Auger bit....................................... High:
Ship-auger bit............................... High:
Self-feed bit .................................. High:
Steel ................................................. High:
No load speed (min
Overall length (with an extended spade grip)
............................................................... 330 mm (410 mm)
Net weight ........................................... 4.7 kg
Safety class ......................................... Class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for drilling in wood, metal and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool's plug.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
4
Downloaded from www.Manualslib.com
Explanation of general view
6 Spade grip
7 Hex. bolt
8 Chuck key
9 Reaction
10 Forward
Low:
Low:
Low:
Low:
-1
) ......................... High:
Low:
I
manuals search engine
DRILL SAFETY WARNINGS
DA6301
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
29 mm
2. Hold power tool by insulated gripping surfaces,
38 mm
when performing an operation where the cutting
38 mm
accessory may contact hidden wiring or its own
38 mm
cord. Cutting accessory contacting a "live" wire may
35 mm
make exposed metal parts of the power tool "live"
118 mm
and could give the operator an electric shock.
13 mm
3. Always be sure you have a firm footing.
13 mm
Be sure no one is below when using the tool in
1,200
high locations.
300
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
8. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
ENE032-1
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
ENF001-1
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
GEA010-1
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
• Change the direction of rotation only when the tool
comes to a complete stop. Changing it before the tool
stops may damage the tool.
The switch is reversible, providing either clockwise or
counterclockwise rotation. To start the tool, simply pull
the lower part of the switch trigger for clockwise or the
upper part for counterclockwise. Release the switch to
stop.
11 Reverse
12 Limit mark
13 Screwdriver
14 Brush holder cap
GEB001-6