Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4.7 Deactivation of the Machine
- If the sawing machine is to be out of use for a long period,
it is advisable to proceed as follows:
1)
Detach the plug from the electric supply panel
2)
Loosen blade tension
3)
Release the saw arm counter-balance spring
4)
Empty the coolant tank
5)
Carefully clean and grease the machine
6)
If necessary, cover the machine.
4.8 Dismantling (out of service)
General rules:
If the machine is to be permanently demolished and/or
scrapped, divide the material to be disposed of according
to type and composition, as follows:
1)
Non-composite cast iron or ferrous materials are
recyclable raw materials, so they may be taken to an
iron foundry for re-melting after having removed the
contents (classified in point 3).
2)
Electrical components, including the cable and
electronic material (magnetic cards, etc.), fall within
the category of material classified as being
assimilated to urban waste according to the laws of
your local, state, or federal government, so they may
be set aside for collection by the public waste disposal
service;
3)
Old mineral and synthetic and/or mixed oils,
emulsified oils and greases are considered hazardous
to the environment, so they must be collected,
transported and disposed of at a special waste
disposal service.
CAUTION:
The legislation concerning waste disposal and recycling is in
a constant state of evolution, therefore is subject to
changes. The user must keep informed of the regulations
at the time of disposal as these may differ from those
described above.
5.0 Electrical Connections
WARNING:
All electrical connections must be done by a qualified
electrician in compliance with all local codes and
ordinances. Failure to comply may result in serious
injury.
The SX-835DGSVI Metal Band Saw is rated at 3~400V, PE,
50Hz power supply, the machine comes with a plug
designed for use on a circuit with a grounded outlet.
Mains connection and any extension cords and plugs used
must comply with the information on the machine license
plate.
The mains connection must have a 16A surge-proof fuse.
Only use extension cords marked H07RN-F, with wires
2
1,5mm
or more.
The total length of cord may not exceed 18 Meter
Power cords and plugs must be free from defects.
Connections and repairs to the electrical equipment may
only be carried out by qualified electricians.
The machine is equipped with 1.8m power cord and plug.
Before connecting to power source, be sure the main
switch is in OFF position.
5.1 Grounding instructions
This tool must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The
plug must be inserted into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING:
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do
not modify the plug provided with the tool.
The green/yellow conductor is the equipment-grounding
conductor. If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-grounding
conductor to a live terminal.
Use only 3-wire extension cords with grounding plugs.
Repair or replace damaged or worn cord immediately.
5.2 Extension cords
The use of extension cords is discouraged; try to position
machines near the power source. If an extension cord is
necessary, make sure it is in good condition.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Only use extension cords marked H07RN-F, with wires
2
1,5mm
or more.
The total length of cord may not exceed 18 Meter
Extension cords and plugs must be free from defects.
12
Werbung
Kapitel
Inhaltsverzeichnis
