Switching Off - EINHELL GE-LC 18 Li T Originalbetriebsanleitung

5.10 Removing the chain saw mounting kit
from the motor head (Fig. 19 – 20)
The cutter guard must be slipped over the moun-
ted cutter bar with saw chain in order to prevent
injuries.
1. Pull the lock button (R) to the right.
2. Turn the chain saw mounting kit to the point
where the arrows on the motor head and
chain saw mounting kit coincide, allowing the
mounting kit to be removed.
5.11 Fitting the battery (Fig. 22 – 23)
Press the side pushlock button (T) of the battery
pack as shown in Fig. 22 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 23, make sure that
the pushlock button latches in place! To remove
the battery pack, proceed in reverse order.
5.12 Charging the battery (Fig. 24)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button (T).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(21) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (1) into the battery
charger (21).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Anl_GE_LC_18_Li_T_SPK9.indb 26 Anl_GE_LC_18_Li_T_SPK9.indb 26
GB
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Caution! Always use the shoulder strap when
working with the equipment. Always switch off the
equipment before you take off the shoulder strap.
Otherwise there is a risk of injury.
Put on the shoulder strap as described above, fi t
the required mounting kit and adjust the equip-
ment to suit your needs.
Switching on/off
Switching on
•
Hold the equipment by the handles with both
hands (thumbs under the additional handle).
•
Slide the safety lock-off (Fig. 3/Item 4) to the
front and hold.
•
Switch on the equipment with the On/Off
switch (Fig. 3/Item 3). You can then release
the safety lock-off.
Switching off
Release the On/Off switch (Fig. 3/Item 3).
7. Working with the chainsaw
mounting kit
Preparations
To ensure that you can work safely, check the fol-
lowing points before every use:
Condition of the chainsaw
Inspect the chainsaw before the start of work for
damage to the housing, the power cable, the saw
chain and the cutter rail. Never use a chainsaw
which is obviously damaged.
Oil container
Fill level of the oil container. Even while working,
keep checking that suffi cient oil is in the system.
- 26 -
27.10.2020 10:20:11 27.10.2020 10:20:11