Werbung
1. PARTS LIST: 1. Head Support; 2. Seat cover; 3. Buckle ; 4 . Webbing Adjuster; 5. ISOFIX Attachments Releasing Button; 6. Recline Adjustment Handle ;
7. Crotch Strap; 8. Shoulder Strap; 9. Infant Insert ;10. Rear-facing Lock-off ;11. Group 1 Lock-off Device 12. Head Support Adjustment Lever;
13. Tether Strap Adjuster ;14. Tether Hook; 15 Top Tether Strap; 16. Instruction ManualStorage Compartment;17. Base; 18. ISOFIX Attachments
Connector;19. Seat Belt Guiding; 20. ISOFIX Attachments;
Make sure all parts are available before assembly. If any part is missing, please contact local retailer. No tools are required for assembly.
Soft goods include Head Support, Seat Pad, Shoulder Strap, Crotch Strap and Infant Insert.
2. CONCERNS ON INSTALLATION: SHOWS THE CORRECT WAY FOR INSTALLATION ON FIGURE 2
3. THIS CHILD SEAT OFFERS A VARIETY OF INSTALLATION OPTIONS: The following table indicates the types of installation for respective groups: see Figure 3.
4. RECLINE ADJUSTMENT
Press the recline adjustment handle, and adjust the child restraint to the proper position. Figure 4.1
The recline angles are shown as There is 3 recline angles for rear facing baby mode. Figure 4.2
There are four recline angles "1-4" for toddler mode Angle indication: with top and bottom triangles aligned. Figure 4.2
There is one recline angle for 1 junior mode, it is marked as "1" red triangle. Figure 4.2
Make sure that vehicle seat belt will be tight when adjusted in reclining position and vice versa if seat was already buckled up properly previously.
5. HEIGHT ADJUSTMENT FOR HEAD SUPPORT AND SHOULDER HARNESSES
Please adjust the headsupport andshoulder harnesses toproper height accordingtothe child's height. (Figure 5, 1 2 3）
When used in Group 0+,the shoulder harness height must be even with child's shoulders.
When used in Group I,II, the shoulder harness height must be even with child's shoulders.
When used inGroup III the shoulder belt guides must be even with child's shoulders.
If the shoulder harnesses are not at proper height, the child may be thrown from the child restraint when there is an accident.
Squeeze the head support adjustment lever,meanwhile pull up orpush down the head support until it snaps into one of the11positions. (Figure 6)
7. INSTALLING IN GROUP 0+
(Rearward Facing Mode/for Child under 18kg)
Please install the child restraint on the rear vehicle seats and then put the child in the child restraint.(Figure 7.1)
Please adjust the child restraint to proper angle (3 positions). Angle indication: With top triangle and blue triangle aligned.Make sure the shoulder harness is adjusted
to proper height before installing this child restraint. When installing and adjusting the safety belts, make sure that both the shoulder belt and the waist belt are not
twisted and will not stop the safety belts from functioning properly.
1. Pass the waist belt over lap belt guidings, and then engage the vehicle buckle tongue into the buckle.(Figure 7.2)
2. Fasten the shoulder belt in the two shoulder-belt slots at the back of the child restraint.
Shoulder belt must pass through the Lock-o . Ensure the belt lock o cover is completely closed when not in use to prevent injury, or damage to vehicle upholstery.(Fig-
ure 7.3)
3. While pressing the child restraint, pull the belts to fasten the child restraint tightly and securely.(Figure 7.4) ! The child restraint can not be used if the
vehicle safety belt buckle (female buckle end) is too long to anchor the child restraint securely. (Figure 7.5) .Please check by moving the child restraint back and forth.
(Figure 7.6)
Correctly assembled vehicle belt is shown as (Figure 7.7)
• Waist belt passes through the lap belt guidings.
• Shoulder belt must passes through the shoulder-belt slots.
• The vehicle buckle tongue is engaged with the buckle correctly.
8. SECURING YOUR CHILD IN THE CHILD RESTRAINT USE INFANT INSERT
8.1 We recommend using the full Infant insert while the baby is 0-9 months. The infant insert increases side impact protection.
8.2 Detach the snaps on the head support to remove the head portion of the insert.
8.3 Remove the head support portion of the infant insert when the child's head no longer ts comfortably. Remove the body portion of the infant insert when the
shoulders no longer t comfortably.
8.4 Remove the infant insert cushion by detaching the snaps to allow more space when the infant does not t comfortably. The cushion can be used separately without
being attached to the insert tobolster the infant's back for more comfort.
9. HARNESS INSTALLATON IN GROUP 0+
9.1 While pressing the harness adjustment button, pull completely the two shoulder harnesses ofthe child restraint. (Figure 9.1)
9.2 Press the red button to unlock the buckle.(Figure 9.2)
9.3 Place the child in the child restrain and pass both arms through the harnesses. Engage the buckle. (Figure 9.3)
9.4.Pull down the adjustment webbing and adjust it to the proper length to make sure your child is snugly secured.
After the child is seated, recheck whether the shoulder harnesses are at the proper height. Make sure the space between the child and the shoulder harness is about the thickness of
one hand. (Figure 9.4)
10. INSTALLING IN GROUP I,II (Forward Facing Mode/ for Child between 9-18kg)
Please install the child restraint on the vehicle seat, and then put the child in the child restraint.
Please adjust the child restraint to proper angle (4 positions).
Angle indication: With top triangle and red triangle aligned.
Please adjust the shoulder harnesses to proper height before installing the child restraint. When installing and adjusting the safety belts, make sure that both the shoulder belt and
the waist belt are not twisted and will not keep the safety belts from being properly positioned.
For installation with 3-point-belt
10.1. Thread the safety belt through two seat belt back slots at the back of the child restraint.(Figure 10.1)
10.2. Buckle the safety belt.(Figure 10.2)
10.3. Open the lock-off device and insert the safety belt through it. (Figure 10.3)
10.4. While pressing the child restraint, pull the belts to fasten the child restraint tightly and securely. The child restraint can not be used if the vehicle safety belt buckle (female buckle
end) is too long to anchor the child restraint securely. Please check by moving the child restraint back and forth. (Figure 10.4)
ENGLISH
Werbung
