Noise Emission Values; Technical Data; Before Putting The Machine Into Operation - EINHELL UZS 18/250 Bedienungsanleitung

Anleitung UZS 18-250 SPK 1

Noise emission values

Sound pressure level LPA 97,7 dB(A)
Sound power level LWA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.

5. Technical data

AC motor
Power P
Idle speed n
0
Cutting-off wheel
Number of teeth
Table size
Drag length
Cutting height max.
Height adjustment
Tilting saw blade
Extractor socket
Weight
Vibration
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
Downloaded from www.Manualslib.com
17.03.2005 9:32 Uhr
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
Idle mode
that the saw blade is correctly fitted and that the
93,2 dB(A)
machine's moving parts run smoothly.
109,3 dB(A) 96,3 dB(A) Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembly
Place the saw on a flat and firm surface.
Fasten the extractor adapter (16) with the 2
screws (35) to the back of the saw as shown in
Fig. 5.
Fit the extension pipe (50) for the lower dust
extraction device and the short extractor hose
(51) to the extractor adapter and extension pipe.
230V - 240V 50Hz
7.2 Fitting / removing the saw blade guard (Fig.
S1 1500 W S6 40% 1800 W
2/3)
4300 min -1
Mount the saw blade guard (2) on the splitter (5)
Ø 250 x Ø 30 x 2.4 mm
so that the screw fits through the hole (44) in the
48 splitter.
Do not tighten the screw (15) too far – the blade
660 x 456 mm
guard must be able to move freely.
220 mm
Fasten the extractor hose (13) to the extractor
73 mm / 0°
adapter (16) and to the extractor socket of the
50 mm / 45° blade guard (2).
A suitable extractor system has to be connected
infinite 0 -73 mm
to the outlet of the extractor adapter (16).
infinite -2° -47°
To remove the saw blade guard, proceed in
Ø 35 mm
reverse order.
33 kg Important!
The guard hood (2) must always be lowered
2.07 m/s 2
over the workpiece before you begin to cut.
7.3. Setting the splitter (Fig. 8/9)
Important! Pull out the power plug.
Set the blade (4) to max. cutting depth, move to
0° position and lock in place.
Remove the saw blade guard (see 7.3).
Take out the table insert (6) (see 7.5).
Slacken the fixing screw (20).
7.3.1. Setting for maximum cuts (Fig. 6/7/8)
Push up the splitter (5) until the gap between the
saw table (1) and the upper edge of the splitter
(5) equals approx. 10 cm.
The distance between the blade (4) and the
splitter (5) should be 3-8 mm.
Retighten the screw (20) and mount the table
manuals search engine
Seite 19
GB
19