Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL NEW GENERATION NMS 210 Originalbetriebsanleitung

Anleitung_NMS_210_SPK7:_
GB
pressure to move the machine head through the
workpiece.
When the cut is completed, return the machine to
its top parking position and let go of the On/Off
switch.
Caution! A return spring causes the machine
head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut
is completed but steady the machine head and
allow it to rise slowly.
7.2 90° cross-cuts and 0°-45° rotary table (Fig. 8)
The crosscut saw can be used to make right and left
angular cuts of 0°- 45° in relation to the stop rail.
Lift the machine head (4) to its top position.
Release the turntable (8) by slackening the
locking grip (10).
Using the handle (2), set the turntable (8) to the
desired angle, i.e. the marking (a) on the
turntable must coincide with the desired angular
setting (17) on the stationary base plate (9).
Re-tighten the locking handle (10) in order to fix
the rotary table (8) in position.
Make the cut as described in Section 7.1).
7.3 Mitre cuts 0°-45° and rotary table 0° (Fig. 6/9)
The crosscut saw can be used to make miter cuts of
0° - 45° in relation to the work face.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until the pointer (11) coincides with the required
angle value (15).
Re-tighten the locking nut (12) and make the cut
as described in Section 7.1).
7.4 Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 10)
The crosscut saw can be used to make miter cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° in relation to the stop rail
(double miter cut).
Lift the machine head (4) to its top position.
Release the turntable (8) by slackening the
locking grip (10).
Adjust the rotary table (8) by its handle (2) to the
required angle (see also Section 7.2).
Retighten the tightening screw (10) in order to
secure the turntable in place.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until it coincides with the required angle value (in
this connection see also section 7.3).
Screw the tightening screw (12) back down
again.
14
12.07.2010 7:39 Uhr Seite 14

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
9.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
9.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
Lubricate all moving parts at regular intervals.
9.4 Ordering replacement parts
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info