Replacing The Power Cable - EINHELL BT-MS 250 L Originalbetriebsanleitung

6.4 Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 10)
The crosscut saw can be used to make miter cuts
to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° in relation to the
stop rail (double miter cut).
•
Lift the machine head (4) to its top position.
•
Undo the rotary table (8) by slackening the lo-
cking handle (10) and pressing the latch (11).
•
Adjust the rotary table (8) by its handle (2) to
the required angle (see also Section 6.2).
•
Retighten the tightening screw (10) in order to
secure the turntable in place.
•
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
left until it coincides with the required angle
value (in this connection see also section
6.3).
•
Screw the tightening screw (12) back down
again.
•
Make the cut as described in Section 6.1).
6.5 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (14) for
sawdust and chips.
The debris bag (14) can be emptied by means of
a zipper at the bottom.
6.6 Replacing the saw blade (Fig. 1/11-15)
•
Pull out the power plug.
•
Swing up the machine head (4).
•
Press the release lever (1) and flip the saw
blade guard (6) up.
•
Slacken the two screws (27) by 2-3 turns
and swing back the support plate for the saw
blade guard (29) and the saw blade guard (6)
(Fig. 12-13).
•
Press the saw shaft lock (35) with one hand
while holding the wrench (31) on the flange
bolt (18) with the other.
•
Firmly press on the saw shaft lock (35) and
slowly rotate the flange bolt (18) in clockwise
direction. The saw shaft lock engages after no
more than one rotation.
•
Now, using a little more force, slacken the
flange bolt (18) in clockwise direction.
•
Turn the flange screw (18) right out and remo-
ve the external flange (34).
•
Take the blade (5) off the inner flange and pull
out downwards.
•
Mount the new saw blade in reverse order
and fasten.
•
Important! The cutting bevel of the teeth, i.e.
the direction of rotation of the saw blade, has
to conform with the direction of the arrow
Anl_BT_MS_250_L_SPK1.indb 25 Anl_BT_MS_250_L_SPK1.indb 25
GB
marked on the housing.
•
Clean the saw blade flanges thoroughly befo-
re mounting the saw blade.
•
Reattach the movable blade guard (6) in re-
verse order.
•
Before using the saw again, check that the
safety devices are in good working order.
•
Important: Every time that you change the
saw blade, check to see that it spins freely in
the groove of the turntable in both perpendi-
cular and 45° angle settings.
6.7 Laser function (Fig. 17)
•
You can switch the laser ON and OFF with
the switch (a).
•
The laser directs a beam onto the workpiece.
•
Extremely precise cuts can be made using
the laser function.
6.8 Replacing the battery (Fig. 18-19)
Ensure that laser (21) is switched off . Remove
the battery compartment cover (36). Remove the
spent batteries and replace them with new ones
(2 x 1.5 V type R02, LR 03 Micro, AAA). Check
that the battery terminals are positioned correctly.
Close the battery compartment again.

7. Replacing the power cable

If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 25 -
07.05.12 10:38 07.05.12 10:38