User Information; Safety Instructions; Product Description; Intended Use - Bosch 1 687 010 402 Originalbetriebsanleitung

en 16 | 1 687 010 402 / ... 493 |
2.

User information

2.1 Important notes
Important information on copyright, liability and war-
ranty provisions, as well as on equipment users and
company obligations, can be found in the separate
manual "Important notes on and safety instructions for
Bosch Diesel Test Equipment". These instructions must
be carefully studied prior to start-up, connection and
operation of the 1 687 010 402 / ... 493 and must always
be heeded.
2.2

Safety instructions

All the pertinent safety instructions can be found in
the separate manual "Important notes on and safety
instructions for Bosch Diesel Test Equipment". These
instructions must be carefully studied prior to start-up,
connection and operation of the 1 687 010 402 / ... 493
and must always be heeded.
2.3

General Instructions

These instructions are only valid in conjunction with the
instructions supplied for the:
R
Injection pump test bench EPS 708 (1 689 989 067)
and / or injection pump test bench EPS 815
(1 689 979 672)
R
Continuous flow-rate measurement system
KMA 802/822 (1 689 979 674)
R
Test set for common rail pumps CRS 845
(1 689 989 069)
These instructions must also be kept together with and
forwarded together with the instructions listed above.
|
1 689 989 211 2015-08-04
3.

Product description

3.1

Intended use

These accessory sets contain clamping accessories and
connection accessories for the testing of common rail
pumps CB 18 (hereinafter referred to as CB 18) in con-
junction with the EPS 708, with lubricating oil supply, or
in conjunction with the EPS 815, with lubricating oil sup-
ply and test set CRS 845.
3.2 Prerequisites
R
EPS 708 or EPS 815
R
Test set CRS 845H (1 687 002 845).
R
Software EPS 945
R
Operating knowledge on the EPS 708 with lubricat-
ing oil supply, and / or EPS 815 with lubricating oil
supply, and on test set CRS 845.
R
Good knowledge of the mode of operation of com-
mon rail pumps.
3.3

Scope of delivery

3.3.1 Accessory set 1 687 010 402
i
This set is for CB 18 with cone shaft connection.
Designation
Fixing flange (for flange  68 mm)
Reducing ring (D1 = 68 mm / D2 = 50 mm)
Hexagon bolt (3 x M8 x 30 ISO 4017-8.8)
Washer (3 x DIN 125 - A 8, 4 - ST)
Coupling half (D 20 mm, M14 x 1.5)
Mounting sleeve for coupling half
Mounting wrench for coupling half
Hose line
Union nut (A2 L15 DIN 3870)
Cutting ring (15 DIN 3861)
Hose fitting (M 6, G 1 / 8")
Flat sealing ring (DIN 7603 A 6 x 10 x 1 mm)
Plug-in nipple
Flat sealing ring
(DIN 7603 A 10 x 13.5 x 1 mm)
Banjo union (for M10 x 1, D= 8 mm hose)
Screw clamp (10 - 16 mm)
Threaded socket (M10 x 1, ISO 8434 - 1- L 10)
EP software EPS 945 Vers. 2014/C or higher 1 687 000 956
CD-TestData Vers. 2014/C or higher
i
The order numbers in the 'Scope of delivery' chapter
are only for information.
Part number
1 685 720 353
1 680 103 609
–
–
1 686 430 055
1 680 506 040
1 687 951 030
1 680 712 367
–
–
1 683 457 128
1 684 484 012
–
1 683 385 063
–
1 683 356 133
1 687 370 270
Robert Bosch GmbH