General Power Tool Safety Warnings; Cut-Off Machine Safety Warnings; English (Original Instructions) - DeWalt DWE46225 Übersetzung Der Originalanweisung

125 MM CUTTING SHROUD
DWE46225
230 MM CUTTING SHROUD
DWE46229
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.
Technical Data
Type
These cutting shrouds are for use only with D
technical specifications:
guard holder diameter mm
max. diamond wheel diameter mm
wheel body thickness mm
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.

DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.

Denotes risk of electric shock.

Denotes risk of fire.

GENERAL POWER TOOL SAFETY WARNINGS


WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with
this cutting shroud. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.

WARNING: Read all the safety warning and instructions
of the power tool and dust extractor connected to the
shroud. Failure to follow all warnings and instructions
listed in these manuals may result in electrical shock, fire
and/or seious injury.
WALT one of the
e
DWE46225 DWE46229
1 1
WALT grinders with following
e
44.4 60
125 230
1.2 1.8
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.

CUT-OFF MACHINE SAFETY WARNINGS

a ) The guard provided with the tool must be securely
attached to the power tool and positioned for
maximum safety, so the least amount of wheel is
exposed towards the operator. Position yourself
and bystanders away from the plane of the rotating
wheel. The guard helps to protect operator from broken
wheel fragments and accidental contact with wheel.
b ) Use only diamond blades for your power tool. Just
because an accessory can be attached to your power tool,
it does not assure safe operation.
c ) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed can
break and fly apart.
d ) Wheels must be used only for recommended
applications. For example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels are intended
for peripheral grinding, side forces applied to these wheels
may cause them to shatter.
e ) Always use undamaged wheel flanges that are of
correct diameter for your selected wheel. Proper
wheel flanges support the wheel thus reducing the
possibility of wheel breakage.
f ) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
g ) The arbour size of wheels and flanges must properly
fit the spindle of the power tool. Wheels and flanges
with arbour holes that do not match the mounting
hardware of the power tool will run out of balance, vibrate
excessively and may cause loss of control.
h ) Do not use damaged wheels. Before each use,
inspect the wheels for chips and cracks. If power tool
or wheel is dropped, inspect for damage or install an
undamaged wheel. After inspecting and installing
the wheel, position yourself and bystanders away
from the plane of the rotating wheel and run the
power tool at maximum no load speed for one
minute. Damaged wheels will normally break apart
during this test time.
EnGLIsh
17