Technical Features; Water Connections - Jacuzzi AlimiaExperience Vorinstallationsblatt

It is the responsibility of the installer/owner to ascertain
compliance with specific local regulations prior to installa-
tion.
Jacuzzi Europe S.p.A. gives no guarantee in this respect
and refuses all responsibility regarding compliance of the
installation carried out.

Technical Features

i
Alimia Experience ( 1) requires about 2,100 litres water alto-
gether, about 1,500 for the Minipool and about 600 in the com-
pensation tank and the water circuit. The electricity supply is three-
phase, 380-415 V (European standard) or, on request, 220-240 V,
always three-phase.
It includes:
- a control unit, called "Spa-Pak"
- the compensation tank (
required to hold water that overflows when users get into the tub.
Its nominal capacity is 1,000 litres (operating with about 800-850
litres).
i
- the Minipool ( 1, C), is to be connected, with hoses, to the
"Spa-Pak", the compensation tank and the drain.
Alimia Experience is equipped with multi-colour spotlights (12V).
MAXIMUM ABSORPTION FOR THE SYSTEM
• version without blower
Power supply Total consumption electric hea-
(three-phase) ter + pumps + spotlights
Voltage Hertz Ampere
(*)
220 - 240 3~
50
380 - 415 3N~ 50
(*): special standard (does not apply to Europe)
• version with blower
Power supply Total consumption electrical heater
(three-phase) + pumps + spotlights + blower
Voltage Hertz Ampere
220 - 240 3~ (*)
50
380 - 415 3N~ 50
(*): special standard (does not apply to Europe)
WEIGHTS
MINIPOOL
Net weight Water volume
kg
litres
~ 1500
~180
area involved resting surface
m 2
m 2
~1,12
~4,4
Max. weight
when full
kg
COMPENSATION
~925
TANK
~285
SPA-PAK
i
( 1, A) .
i
1, B) which, once connected, is
Total consumption only pumps and
spotlights (version with exchanger)
kW Ampere
(j)
18,5
41 12
(j)
18,5
23 7
(j): Max. absorbed power
Total consumption only pumps, blower
and spotlights (version with exchanger)
kW Ampere
(j)
20
50 21
(j)
20
28 12
(j): Max. absorbed power
Max.
No. of people
n
6-7
average load on area concentrated load on
involved resting surface
kg/m 2
~510
resting surface
at floor level
m 2
~1,2
~1,1
Components
Components and the necessary connections for setting up the system
are described below (see
Minipool and hosing
1 overflow channel with grid
2 pneumatic buttons
2a box for connection of pneumatic buttons
3 low-point drain with gate valve
to the compensation tank (overflow lines)
4a1-4b1
from the overflow channel (overflow lines)
4c1-4c2
5 hydromassage pump suction lines
6 hydromassage pump delivery lines
7 filtering suction line
8 suction line from the compensation tank
9 filtering return line
10 blower line (optional)
11 connections to the water system
12 perimeter metal supports
Spa-pak
13 Electric wiring box
14 optional - 14b: heater (12 kW) or 14a: heat exchanger
(40.000 Kcal/h)
15 hydromassage pumps (2 + 2 Hp)
16 filtering pump (0.75 Hp)
17 blower (optional)
18 quartz sand filter
19 safety switch
20 temperature sensor
Compensation tank
kW
21 water loading/filling solenoid valve (3/4")
(j)
5
22 level switches
(j)
5
23 check valve
24 gate valve (for emptying)
25 pre-filters
26 overflow
27, 28 ground drainage points
kW 29 gate valves (for system maintenance)
(j)
6,5
30 gate valves (for suction balancing)
(j)
6,5
31 hose draining (areas at risk from ice)

Water connections

I
The hosing system (including connectors, gate valves, etc.,
Total
max. weight
connecting the Minipool to the Spa-Pak and the compensation tank,
kg
must be set up by the installer.
~2240
I
The Customer must provide the ground drainage points (
detail 27 and 28) of suitable dimensions, which can be inspected for
kg/m 2
any cleaning, and to which the low-point drain ø 50 mm (
~2000
3), the loading/overflow of the compensation tank and the drain from
the filter are to be connected.
load
at floor level
CAUTION! Before preparing the ground drainage points,
kg/m 2
consult the local authority for the regulations that control
~770
the drainage of chemically treated water.
~260
13
i
2).
i
2) for
i
2,
i
2, detail