Manufacturer's Warranty; Spare Parts Lists - Roller Disc 100 Betriebsanleitung

eng
5.6. Fault: Cutting wheel becomes blunt or breaks out after 1 or 2 cuts.
Cause:
● Cutting in a cutting notch in which the previous cutting wheel already
became blunt or was damaged.
● Unsuitable cutting wheel.
● Pipe material is unsuitable for cutting.
5.7. Fault: Cutting of the pipes leaves marks on the outside of the pipes.
Cause:
● Rollers (3) of the pipe cutting machine and/or the roller insert (14) soiled.
● Rollers (3) of the pipe cutting machine and/or the roller insert (14)
damaged.
5.8. Fault: A wavy cutting edge is made when cutting stainless steel drainpipes/downpipes (EN 1124) with ROLLER'S Disc 100 RF.
Cause:
● Feeding pressure too high.
● Blunt/broken cutting wheel.
● Unsuitable cutting wheel.
5.9. Fault: ROLLER'S Akku-Disc 100 22 V stops, the LED of the machine status check (18) fl ashes red.
Cause:
● Motor temperature exceeded.
6. Disposal
ROLLER'S Disc 100, ROLLER'S Disc 100 RF, ROLLER'S Akku-Disc 100 22 V,
ROLLER'S Disc 225, batteries and rapid chargers may not be thrown in the
domestic waste after use. They must be disposed of properly by law. Lithium
batteries and battery packs of all battery systems may only be disposed of in
the discharged state, all contacts of incompletely discharged lithium batteries
and battery packs must be covered with insulating tape.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which ROLLER is not responsible, shall be excluded from the
warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station authorized by ROLLER
without prior interference and in a fully assembled condition. Replaced products
and parts shall become the property of ROLLER.
Remedy:
● Place the cutting wheel next to the notch with the remaining fragments.
● Select and change cutting wheel according to the pipe to be cut.
● Only use approved pipes, see 1.3.
Remedy:
● Clean rollers with machine cleaner (Art. No. 140119), then protect against rust.
● Change rollers.
Remedy:
● Reduce feeding pressure.
● Change cutting wheel.
● Use ROLLER'S cutting wheel RF (Art. No. 845054).
Remedy:
● Wait until the LED lights green. Switch on the ROLLER cordless tool and let it
run without load to shorten the cooling time.
The user shall be responsible for the cost of shipping and returning the product.
A list of the ROLLER-authorized customer service stations is available on the
Internet under www.albert-roller.de. For countries which are not listed, the
product must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is Albert
Roller GmbH & Co KG, Neue Rommelshauser Straße 4, 71332 Waiblingen,
Deutschland.

8. Spare parts lists

For spare parts lists, see www.albert-roller.de → Downloads → Parts lists.
eng
17