Herunterladen Inhalt Inhalt Diese Seite drucken

Machine Assembly - Stiga B 1.0 EJ Gebrauchsanweisung

Elektrischer freischneider / trimmer
Vorschau ausblenden Andere Handbücher für B 1.0 EJ:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 43
6
EN

4. MACHINE ASSEMBLY

WARNING!
very carefully so as not to impair the safety
and efficiency of the machine. If in doubt, con-
tact your dealer.
WARNING!
not plugged into the mains socket.
WARNING!
ing the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always making
use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
1. MOUNTING THE FRONT HANDGRIP
(Fig. 1)
WARNING!
(1) is to ensure a minimum distance between
the rear handgrip and the front one, for safety
reasons. This spacer must always be fitted
and must not be modified in any way.
– Fit the lower part (3) with guard on the drive tube
– Fit the front handgrip (4) by using the screws (5).
– Before tightening the screws (4), align the hand-
grip correctly with respect to the drive tube.
– Fully tighten the screws (4).
2. MOUNTING THE ROD (Fig. 2)
– Push the lower part of the rod (1) right down un-
til the stop pin (2) clicks into the hole (3) in the
rod. This is easier to do if you rotate the lower
part of the rod (1) slightly in both directions; in-
sertion is completed when the stop pin (2) pro-
trudes completely from the hole (3).
– Once inserted, tighten the knob (4) securely.
3. MOUNTING THE GUARD (Fig. 3)
WARNING!
with the same guard for grass trimmer and
Mount the components
Make sure the machine is
Unpacking and complet-
The purpose of the spacer
The machine is supplied
brush cutter provided. The guard cannot be
changed. No other guard except the one pro-
vided may be used.
– Remove the blade (if fitted) as described in para-
graph 4.
– Loosen the two screws (1) and remove the cap
(2) with its bracket (3).
– Apply the guard (4) and refit the cap (2), tight-
ening the two screws (1) in the holes in the
bracket (3).
• Mounting the additional guard (Fig. 4)
– Assemble the additional guard ( 5 ) by clicking
the tabs ( 6 ) into place in their respective slots
in the guard ( 4 ). Ensure that the tabs click in
completely.
4. REMOVING AND REFITTING
THE CUTTING DEVICES
WARNING!
devices or ones homologated by the Manu-
facturer.
• 3 point blade (Fig. 5)
WARNING!
and fit the blade guard.
NOTE
left-hand thread and so must be unscrewed in a
clockwise direction and screwed up anticlockwise.
– Unscrew the nut (5) clockwise.
– Pull out the outer ring-nut (7), then remove the
blade (1).
– Pull out the washer (6) and the outer ring-nut (7)
and remove the blade (1).
When mounting,
– Ensure that the grooves in the inner ring-nut (8)
match up perfectly with the angle transmission
(3).
– Fit the blade (1) and outer ring-nut (7).
– Refit the nut (5) fully tightening it in an anti-clock-
wise direction.
– Remove the wrench (2) to restore blade rotation.
MACHINE ASSEMBLY
Use only original cutting
Wear protective gloves
The fastening nut (5) has a

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Sb 1000 j

Inhaltsverzeichnis