Maintenance - Chicco Scoop Gebrauchsanleitung

CLEANING AND MAINTENANCE
The cleaning and maintenance of this product must be carried
out on a regular basis by the user. The cleaning and maintenance
of the stroller must only be carried out by an adult.
CLEANING
The cover can be removed (please refer to the section "How to
Remove the Fabric Cover").
Please refer to the care labels for instructions on how to clean
the fabric parts.
Below are the cleaning symbols and their meanings:
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Periodically wipe clean plastic parts with a soft damp cloth.
Always dry the metal parts to prevent the formation of rust if
the stroller has come into contact with water.

MAINTENANCE

Lubricate the moving parts only if necessary, with a light
application of a silicone based lubricant. Regularly check the
condition of the wheels and, keep them clean of dust and sand.
To avoid friction that may prevent the correct operation of the
stroller, ensure that all the movable plastic parts placed along
the metal frame are clean of dust, dirt or sand. Keep the stroller
in a dry place.
GENERAL INSTRUCTIONS
OPENING
WARNING: When opening the stroller make sure that your
child or other children are at a safe distance. Ensure that during
these operations the moveable parts of the stroller do not
come into contact with the child.
1. Pull simultaneously the trigger operated open mechanisms
located on the stroller handles; the stroller will begin to open
(fi g. 1).
2. Raise the stroller in an upward position to help the opening
operation (fi g. 2).
3. Press the locking mechanism, at the rear of the stroller, in a
downward direction with the point of your foot to complete
the opening operation and lock the stroller in the open
position. (Fig. 3).
WARNING: Ensure that the stroller is locked in the open
position by checking that the locking mechanism at the rear of
the stroller has fi rmly locked into place.
FITTING THE BACKREST
COMPONENTS
A. Backrest adjustment rack
B. Backrest adjustment lever
C. Front joint
D. Front joint seat attachment
E. Lock release knob
F. Rear joint
G. Locking clip
4. To mount the backrest, fi rst fi x the rear joint (F): Rotate the
joint so that the oval seat of it aligns with the stroller tube and,
at the same time, insert the pin on the tube with the hole on
the joint (fi g. 4).
5. Once the pin is in the hole, push the joint until you hear a
click that means the clip is locked (G) as shown in fi gure 5.
Repeat steps 4 and 5 on the other side of the backrest.
6. Now push the front joint (C) in the housing (D) and slightly
pushing on the tube of the backrest, as shown in fi gure 6, until
you hear a locking click. Repeat this operation on the other side
of the backrest.
7. WARNING: Ensure that the backrest adjustment levers (B)
are positioned, after mounting, under the adjustment racks
(fi g. 7 A). Otherwise (fi g. 7 B), unhook the front joint of the
backrest (point 8 in the instructions) and remount it (point 6
of the instructions) taking care to properly position the lever
under the racks.
Fit the fabric cover on the seat, following the "REMOVABLE
LINING" section in stroller instructions backwards.
WARNING: Before using the product in the stroller
confi guration, always check that the backrest is properly
mounted.
REMOVING THE BACKREST
Remove the fabric part of the seat, following the "REMOVABLE
LINING" section in the stroller instructions.
8. First, release the front joint using the side release button
(E) and pull the backrest tube upwards (fi g. 8). Repeat this
operation on the other side of the backrest.
9. Now release the rear joint, pushing the fastening pin (G) and
at the same time pulling the joint inwards (fi g. 9). Repeat this
operation on the other side of the backrest.
REMOVABLE LINING
The lining is fully removable.
Lining removal operations are performed keeping the stroller
partially closed with the safety harness open.
10. Slip off the upper lining of the stroller, taking care for
the crotch strap belt, unfastening the velcro of the seat and
releasing the press studs in the points shown in fi gure 10A and
10B.
11. Finally, slip off the backrest lining by pulling it upwards (fi g.
11).
12. To remove the lower lining:
- Unfasten the two velcro strips from the side tubes (fi g. 12 A);
- Release the press studs located on the armrests and on the
seat in the positions shown in fi gure 12 B, raise 12 C), taking
care for the crotch strap belt of the stroller.
FITTING THE FABRIC
To cover the stroller, follow the instructions shown below.
13. Slip the lower lining of the seat on the leg rest and attach it
using the press studs in the positions shown in fi gure 13, taking
care for the crotch strap belt of the stroller.
14. Fasten the two velcro strips to the side tubes in the positions
shown in fi gure 14.
15. Fit the upper lining on the stroller's backrest (fi g. 15), taking
care for the crotch strap belt of the stroller.
16. Fasten the fabric to the seat by fastening the press studs
and the velcro strips in the positions shown in fi gure 16 A – 16
B.
23