Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Note: Check the straps are adjusted to the child's body and not twisted. Please make sure the safety belt is near the waist, as low as possible and
carefully cinched. Place the child on the seat. Place the straps over the child's shoulders.
7c. Push the buckles together and fasten the lock with a "click".
7d. Carefully pull on the central section of the strap to adjust the belt suitably until the child's body is enveloped by the straps.
8. USING THE RESTRAINT SYSTEM FACING FORWARDS
For babies between 76 and 105cm tall. Adjustable headrest (13 positions). To give your baby the best possible protection, we recommend using
the child restraint system in its rear-facing position as long as possible. If there is insu cient space for the child's legs, then use the seat facing
forwards, as long as the child is at least 76 cm tall.
Note: Accident statistics show that the safest way to transport a child in a car seat is facing the rear. That is why we recommend using this
position as long as possible. The seat should only be used face forwards if:
The child is over 76 cm tall.
The child is over 15 months old.
The headrest is in the 7th position (minimum).
9. USING THE REDUCER CUSHIONS
The pre-installed reducer cushions increase baby safety and comfort. To provide the child with more space, remove the detachable reducers
once the child is 61 cm tall or 3 months old.
9a. Remove the reducer cushion by rst peeling back the headrest cover from where they are located. Remove the memory/visco-elastic foam
to clean the cover. Once washed and dried, reinsert the protectors in the cover.
10. REMOVING THE FABRIC
The fabric comprises 7 components attached to the seat using hooks, clips and snap fasteners. Once all the fastenings have been undone,remove
them one by one and wash them. To reattach the fabric, perform these steps in reverse.
Note: When you replace the belt protectors, you must ensure that:The locked side of the protector lies against the child.
The protector is correctly attached to the strap. The straps run properly through the protector.
WARNING! The textile cover and accessories are key components inthe design to ensure the child's safety. The seat structure cannot be used
without the cover.
11. CLEANING & MAINTENANCE
It is important to use the original seat cover, as it serves a notable purpose for the seat. If it is lost or damaged, replacements can be purchased
from our stores.The seat covers are machine-washable at a maximum temperature of 30º (delicate cycle). Washing at a high temperature may
cause the colour to fade. Please wash the cover separately and do not machine dry.Clean the plastic parts in warm water using a mild detergent.
Do not use chemical detergents or bleaching agents. The integrated harness system cannot be removed fromthe restraint system. Do not
remove parts from the harness system. The harness system can be cleaned in warm water using a mild detergent. Ensure the child restraint
system provides optimal protection by following these points:
All the main components of the car seat must be examined regularly. The mechanical parts must work freely.Ensure the child restraint system
is not blocked by the hard parts, e.g.the car door, rails, etc., which could damage it.Stop dirt or sand getting between the upper section of the
seat and the base. This could have a negative impact on rotation or tilting. If it happens, clean the dirt before rotating or reclining the seat to
prevent damage.
12. PRODUCT DURABILITY
The car seat is designed to comply with its speci cations throughout its life cycle, i.e. approximately 4 years. However, as there may be
unexpected temperature uctuations or changes in the vehicle, bearin mind the following:
Remove the restraint system from the car or cover it with a light cloth if the vehicle is likely to be exposed to direct sunlight for any length of
time.Regularly check all the metallic and plastic parts of the seat for damage, deformity or faded colours. Throw the car seat out if any changes
are found. Changes in the fabric (particularly fading) are perfectly normal when used in a vehicle and have no impact on normal seat functions.
14. PRODUCT RECYCLING
Protect the environment by separating out and eliminating waste from the start (packaging) to the end (product parts) of the life cycle of the
child restraint system. Ensure your car seat is disposed of in accordance with regulations by speaking to the waste disposal agency in your area
or the local authority. Make sure to respect the waste disposal regulations in your country.
15. LIST OF CARS APPROVED FOR THE INSTALLATION OF THE ODISSEY I-SIZE 0+ 1 CAR SEAT
This child restraint system plus base is approved for ECE Regulation R129 / 01. It can be attached to seats in most cars.
Do not use on seats with an active front airbag installed and oriented backwards/rear-facing.
Customers should check with the vehicle manufacturer's manual for the use of the support stand with storage spaces.
If your vehicle is not included in the list in this manual check the vehicle manual or speak to the manufacturer
for further information. List of ECE R129/01 approved vehicles.
ENGLISH
Werbung
