KIKKA BOO ODYSSEY Gebrauchsanweisung Seite 6

1c. Guide the connectors into the ISOFIX anchor point in your vehicle until they click into place. The indicator will change from red to green
on both sides once locked in. Move the seat backwards by pushing the button (4) on the back of the seat.Then, pull the seat towards you to
ensure it is correctly locked in place.
Note: The ISOFIX attachment comprises two metal studs per seat, located in the gap between backrest and seat cushion. In case of doubt,
check with the instruction manual for your vehicle. If it is di cult to access the ISOFIX system, use connecting guiderails (included with the
car seat) to help with the installation and avoiddamaging the upholstery.
Note: Do not place anything in the footwell in front of the child restraint system.
2. ADJUSTING THE POSITION OF THE SUPPORT STAND
2a. Push the button on the support stand (3) and pull until the leg locks into position to ensure optimal placement.
2b. Ensure the indicator on the stand is green (7).
WARNING! The support stand must always be resting on the oor. Do not place any objects under the support stand. For more information
on compartments located in the footwell of some cars, see the instruction manual for your car.
Note: Ensure the i-Size restraint system is at on the seat.
3. REMOVING THE RESTRAINT SYSTEM FROM THE VEHICLE
Follow the installation process in reverse.
3a. Undo the ISOFIX connectors (5) on either side of the child restraint system. Hit the connecting buttons (6) at the same time.
3b. Push the ISOFIX extender button (4) and set it to its shortest length.
3c. Press the buttons (3) on the lower section of the support stand and place it horizontally underneath the seat, i.e. in its original position.-
Fold the front leg under the base.
4. TILT ANGLE ADJUSTMENT
4a. The i-Size restraint system has two tilt positions for the baby`s safety and comfort. To change the position, press the tilt button on the
front of the seat (8).
4b. To adjust the tilt system (9) (facing forward or backwards), switch from rotation to static mode.
WARNING! ROTATION MODE IS ONLY TO ADJUST THE RESTRAINT SYSTEM: DO NOT USE WHEN TRAVELLING. INSTEAD, USE POSITION .
5. USING THE RESTRAINT SYSTEM FACING BACKWARDS
For babies between 40 and 87 cm tall. Adjustable headrest (13 positions)
Note: The reducers/head protectors should be used until the baby is 60 cm tall. Note: The headrest provides the best protection for your baby
if it is set to the right height. It can be set to 13 di erent positions.
5a. The headrest should be set so there is a gap between the child's shoulder and the headrest. Adjust the headrest by pulling on the higher
ring (11), unlocking the mechanism and lowering it into the right position based on the child's height.
Note: the shoulder strap is rmly attached to the headrest and must be adjusted separately.
Note: The child restraint system can be used facing backwards until the child is 87 cm tall. The seat can only face forwards if: The child is over
76 cm tall and at least 15 months old. It is recommendable to use the child restraint system facing backwards as long as possible; The
headrest is set to the 7th position (minimum).
Note: For reasons of safety and ergonomics, newborns and babies that cannot sit unaided until 1 year old must travel facing backwards and
in the most tilted position.
WARNING! If the product is facing the rear, do not place it on a seatwhich has an active front air bag installed.
6. 360º ROTATION
The child restraint system can rotate round 360º. This is to help youplace your baby in the system. It can also be set to "forward-facing or
"rear-facing" positions.
6a. Rotate the child restraint system seat by pushing down on the tilt lever (8).
6b. Place the seat in rotation mode .
WARNING! ROTATION POSITION: Only when the restraint system isin rotation mode and the indicator shows ,can the seat be rotated.
6c. Now press the rotation button (12). and rotate the seat towards the car door, enabling the safety belt to be fastened easily.
7. FASTENING USING THE BELT SYSTEM
Do not use the safety seat without its cover or harness protectors. The shoulder straps are rmly xed in place and must not be adjusted
separately. Note: Ensure the headrest is correctly positioned before using the child restraint system.
Note: Check there are no toys or hard objects on the child restraint system.
7a. Loosen the shoulder straps by pressing on the setting button(13) in the central section of the seat and pulling on the straps at the same
time. Note: Do not pull on the protectors, only on the straps.
7b. Unclip the belt from the buckle by pressing on the red button.
ENGLISH