Installation Instructions; Intended Use; Approval; Tools And Facilities Required - Truma Mover XT4 Gebrauchsanweisung, Einbauanweisung

Installation instructions

Read the installation instructions carefully before commenc-
ing the work, and then comply with them.
Please ensure that no metal chips or other contaminants get
into the control unit during installation.
In the case of screws with sealant, make sure that the
thread is free of grease / oil.

Intended use

The Mover® XT4 has been designed for use on twin-axle
caravans with a gross weight of up to 3100 kg.
The Mover® XT4 weighs approx. 60 kg.
Check the maximum towable weight for your towing
vehicle and the gross weight of your caravan to make
sure that they are designed for this additional weight.

Approval

The Truma Mover® XT4 has design approval, and a "general
operating permit" (ABE) has been issued for Germany. Ac-
ceptance by a vehicle expert is not required (except when
installing the low chassis kit). The general operating permit
(ABE) must be kept in the vehicle.
The Mover® XT4 complies with other requirements of
EC Directives and Standards (see Declaration of conformity).
When installing the Mover® XT4, the technical and administrat-
ive regulations of the country of first registration of the vehicle
must be observed.
Any modifications made to the device, or the use of any spare
parts or functionally significant accessories other than original
Truma parts, or failure to comply with the contents of the op-
erating and installation instructions invalidates the warranty
and precludes any liability claims. This will also invalidate the
operating permit for the equipment.

Tools and facilities required

To install the Mover® XT4 you need:
– 8 mm, 10 mm,13 mm and 17 mm socket wrenches,
ring spanners or open-jawed spanners
– Allen key 4
– Torque wrenches (3.5 – 50 Nm)
– Cable cutter / crimping tool
– Electric drill / screwdriver / keyhole saw, diameter 25 mm
– 2-tonne trolley jack and suitable support trestles
– Adequate lighting

Minimum installation dimensions

A distinction is made between L-profile and U-profile
frames as shown in the illustration.
Caravan floor
L-profile
Figure 6
U-profile
Installation is only possible on caravans with the following
dimensions.
Caravan floor
140
min. 25
min. 35 **
min. 50
min. 1350 / max. 2000
max. 2400
Figure 7
All dimensions in mm.
* with loaded vehicle with max. permissible gross weight
** with U-profile

Measuring the frame height

A frame height of at least 140 mm is required at the level of
the tyre hub / tyre centre in the range of 320 mm from the
outer edge of the tyre.
min.
320
Figure 8

Determining the installation type

1. Standard installation
Standard installation is used with a U-profile or L-profile chassis
and a frame height of at least 140 mm. No special accesso-
ries are required.
2. Installation on chassis with U-profile or L-profile and a
frame height of between 80 mm and less than 140 mm
In order to compensate for height, the 30 mm spacer set (for
frame heights down to 110 mm) or the 60 mm spacer set
(for frame heights of less than 110 mm down to 80 mm) is
required.
3. Installation on chassis with U-profiles or L-profiles
with a frame height of less than 80 mm
If the chassis has a frame height of less than 80 mm, a low
chassis kit must be fitted to compensate for the height.
If a low chassis kit is used in Germany, acceptance
by a vehicle expert is required.
4. Installation on chassis with L-profile and with a lim-
ited amount of space
The short mounting system is required to compensate for
the height (30 or 60 mm) with substructures such as tanks.
min.
320
23