Herunterladen Inhalt Inhalt Diese Seite drucken

General Power Tool Safety Warnings; Work Area Safety; Electrical Safety - Parkside PAS 4 C4 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für PAS 4 C4:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
OUTPUT:
Rated voltage:
Rated current:
Charging time:
Protection class:
Noise and vibration data:
The measured values have been determined in
accordance with EN 62841. The A-rated noise
level of the tool is typically:
Sound pressure level:
Sound power level:
Uncertainty K:
Vibration values (vector total of three directions)
determined in accordance with EN 62841:
Screws:
Vibration emission value:
Uncertainty:
NOTE
The vibration emission values and the noise
emission values given in these instructions
have been measured in accordance with
a standardised test procedure and can be
used for comparison of the power tool with
another tool.
The specified total vibration values and the
noise emission values can also be used to
make a provisional load estimate.
WARNING!
Depending on the manner in which the power
tool is being used, and in particular the kind of
workpiece that is being worked, the vibration
and noise emission values can deviate from
the values given in these instructions during
actual use of the power tool.
Try to keep the load as low as possible.
Measures to reduce the vibration load are,
e.g. wearing gloves and limiting the working
time. Wherein all states of operation must be
included (e.g. times when the power tool is
switched off and times where the power tool is
switched on but running without load).
PAS 4 C4
5.0 V
(DC)
1700 mA
approx. 1 hr
II /
(double insulation)
L
= 67.8 dB (A)
pA
L
= 78.8 dB (A)
WA
K
= 3 dB
pA/WA
a
= 0.79 m/s
2
h
K = 1.5 m/s
2
General power tool
safety warnings
WARNING!
Read all safety warnings, instructions, illust-
rations and specifications provided with this
power tool. Failure to follow all instructions
listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference.
The term „power tool" in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools cre-
ate sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
GB │ IE
 15

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis