Dimplex Living Art Serie Anleitung Seite 6

Ensure the wall plate is fi tted the correct way up i.e. the side
hooks are pointed upwards. - see Fig.3.
The appliance can then be hung on the wall plate by aligning
the slots on the chassis with the side hooks on the wall
plate.
Check to ensure that the bottom hooks have also engaged in
their respective slots.
The corner hinges on the wall plate may be used to secure the
appliance against inadvertent dislodgement. Simply rotate the
the hinges upwards to a position above the chassis (see Fig.2
and Fig.3). They can then be screw fi xed using the screws
removed earlier (see Fig.4, detail 'X', '1').
NOTE: The appliance should be hard wired to a fused switched
spur located behind the glass panel so as to be hidden from
view (see Fig. 1, 'b'). The programme compact fl ash memory
card is factory fi tted and protected by a screw fi xed security
cover, ( see Fig.4 'a') In normal use access to the card is not
a requirement.
Please consult a qualifi ed electrician for appropriate wiring
requirements.
Operation: - LVA192 - LVA192NH
Plug in the IEC connector from the hard wiring outlet to the
IEC fused (SSC 10A 250V) socket on the appliance (see
Fig.1, detail A,1).
The illuminated power 'On' switch (see Fig.5 detail 'Z', 1) must
fi rst be switched 'ON' to operate the appliance.
One of the scenes will automatically show when the power
'ON' switch is operated.
Scene selection and sound control can now be acheived
manually or by remote control, see instructions below.
Note: The user may notice a slight frame freeze lasting less
than 0.5 seconds after a scene has run for approximately
5 minutes. This is normal and should not be a cause for
concern.
Twin fan heaters positioned one left, one right behind the glass
can be operated manually by switch(see Fig.5 detail ' Z', 2) or
by the remote control. Fan operation is indicated by a red light,
which will remain lit while the fans are in use, (see Fig.1 detail
B, 1). Each fan heater has an individual element switch (see
Fig.1 detail C) this provides for cold blow operation if heat is
not required. (LVA192 Only) .
- 2 -
Manual Control Operation: - LVA192 - LVA192NH
The manual controls for the screen are located at the top of the
appliance behind the glass screen (see Fig.4, detail 'Y').
The membrane switch functions are as described below;
Standby Switch 'On'
standby mode. (See Fig.1 detail B,2)
Sound Volume 'Up'
Sound Volume 'Down'
Scene Selection 'Up'
Scene Selection 'Down'
The manual switch for the fan heaters, (see Fig.5 detail 'Z', 2).
Each fan heater has an element switch to provide the option of
hot or cold blow, (see Fig.1. detail C).
The appliance Illuminated Power switch (see Fig.5 detail 'Z',
1) may be used to switch the appliance 'OFF' when it is not
required, say overnight or for long periods, to avoid energy
wastage.
Remote Control Operation: - LVA192 - LVA192NH
The remote control may be operated once the appliance is
switched 'ON' (see Fig.5, detail 'Z', 1).
Aim the remote control at the screen (I.R. sensor is indicated
in Fig.1 detail B, 3) select any one of the eight scenes on your
remote control (see Fig.7)
Each scene has it's own particular sound effect which may be
activated and adjusted up or down by pressing the volume
control buttons (
reached.
The fan heaters may be switched 'ON' and 'OFF' by pressing
the buttons or
operation and will remain lit while the fans are 'ON' (see Fig.1
detail B, 1). (LVA192 Only)
The button functions are identifi ed as described below;
'Coal' Fire scene
'Log' Fire scene
'Embers' Fire scene
'Spring' scene
'Summer' scene
'Autumn' scene
'Winter' scene
'Aquarium' scene
Fan Heater 'ON / 'OFF'. (Hot or Cold blow option
/ 'Off' a red light indicates
(LVA192 Only)
and ) until the level required is
. A red light indicates the fans are in
is by manual selection
LVA192 only)
UK