Before Commissioning; Commissioning - Scheppach HP2500S Original Bedienungsanleitung

8. Before commissioning

m ATTENTION!
Always make sure the device is fully assembled
before start-up!
Wheel kit (fig. B + C)
To manually change the position of the plate compac-
tor, it can be equipped with the enclosed wheel kit.
Switch off the machine engine before attaching the
wheel kit. The machine engine must not be operated
as long as the machine is on the wheel kit. Before
starting the machine, remove the wheel kit!
• Position the wheel kit under the steering bar (8)
• Carefully press the machine forward using the
steering bar (8) so that it is on the front edge of
the base plate (7) and slide the wheel kit under the
base plate (7).
• The wheel kit must be locked into the place with the
locking hook in the base plate hole (7).
• The machine can now be moved using the steering
bar (8)
The wheel kit is disassembly in reverse order.
m Attention: Only use the wheel kit on a level and
solid surface and for short distances.
Paving Pad Kit (fig. D)
The transparent rubber paving pad allows to compact
concrete slabs, stones, bricks and blocks silently and
gently.
Attach the paving pad onto the base plate (7) as
shown. Align the holes in the base plate, paving pad
and clamp plate, and secure it with bolts and flat
washers.
Engine oil (fig. E)
m Check engine oil before commissioning!

9. Commissioning

m ATTENTION!
Always make sure the device is fully assembled
before start-up!
Hand Grip (fig. A; 3)
When operating the compactor, use this hand grip
(3) to maneuver the compactor.
Shift Stick (fig. A; 1 + fig. F)
Push the stick (1) forward, the compactor will move
in a forward direction. Pull the stick (1) backwards,
the compactor will move in reverse direction.
Throttle Control (fig. A; 2)
The throttle lever (2) controls engine speed. Moving
the throttle lever (2) in the directions shown makes
the engine run faster or slower.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
IM_5904613903_HP2500s_191211_new.indd 26 IM_5904613903_HP2500s_191211_new.indd 26
langsam schnell
Fast =
Slow =
langsam schnell
vitesse lente vitesse rapide
vitesse lente vitesse rapide
Handlebar (fig. A; 8)
slow fast
When operating the compactor, this handle (8) is to be
slow fast
in the downward position. When the compactor is to be
Pomalu rychle
Pomalu rychle
stored, move the handlebar (8) to the upright position.
Pomalý rýchly
Pomalý rýchly
Handlebar Latch Pin (fig. G)
hitrega
Počasnega
Počasnega hitrega
Used to lock the handlebar (8) in place in the upward
lassú gyors
position for transporting and stowing. lassú gyors
Press the steering bar (8) forward and lock it with the
бавно бързо
бавно бързо
adjustment bolt.
Nopea hidas
Nopea hidas
Lift Point (fig. A; 4)
Used to lift the machine with crane or other lifting
device.
Belt Guard (fig. H)
Remove this guard to gain access to the V-belt. Nev-
er run the compactor without the V-belt guard. If the
V-belt guard is not installed, the possibility exists that
your hand may get caught between the V-belt and
clutch, thus causing serious injury and bodily harm.
Exciter
An eccentric weight mounted on the exciter shaft
contained within exciter housing is driven at high
speed by a clutch and belt drive system. This high
speed shaft revolution causes the rapid lifting and
downward ramming motion of the machine as well as
imparting a forward motion.
Engine switch (fig. A; 21)
The engine switch (21) enables and disables the igni-
tion system. The engine switch (21) must be in the
ON position for the engine to run.
Turning the engine switch (21) to the OFF position
stops the engine.
Running the engine with dirty oil can cause prema-
ture engine wear and failure.
Changing oil regularly is extremely important.
Oil Drain Hoe (fig. L)
Running the engine with dirty oil can cause prema-
ture engine wear and failure. Changing oil regularly
is extremely important. The flexible oil drain hose is
equipped to drain oil into appropriate receptacle.
Check before operation
Check
Look around and underneath the engine for signs of
oil or gasoline leaks.
Look for signs of damage.
Check that all shields and covers are in place, and all
nuts, bolts, and screws are tightened..
12.12.2019 07:33:39 12.12.2019 07:33:39