Introduction; Device Description (Fig. A); Scope Of Delivery; Proper Use - Scheppach HP2500S Original Bedienungsanleitung

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information. The ma-
chine can only be operated by persons who were in-
structed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with
In addition to the safety instructions in this operating
manual and the separate regulations of your coun-
try, the generally recognised technical rules relating
to the operation of such machines must also be ob-
served.
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
IM_5904613903_HP2500s_191211_new.indd 22 IM_5904613903_HP2500s_191211_new.indd 22

2. Device description (fig. A)

1. Shift stick
2. Throttle Control
3. Hand Grip
4. Lift point
5. Engine
6. Exciter
7. Base plate
8. Handlebar
9. Topping hole for exciter oil
10. Spark plug
11. Muffler
12. Choke lever
13. Fuel tank cover
14. Fuel tank
15. Throttle control assy.
16. Starting lever
17. Recoil starter
18. Air cleaner
19. Oil dipstick
20. Drain plug
21. Engine switch
22. Ventilation screw
23. Oil dipstick
24. Fuel valve

3. Scope of delivery

• Plate compactor
• Transport fixture
• Rubber pad
• Enclosed accessories bag
• Manual

4. Proper use

The plate compactor, for forward or reverse compac-
tion, applies energy to the loose soil or other materi-
als to increase its density and load bearing capacity,
mainly used for general road building projects, the
landscaping sector and in structural engineering.
The loose soil or particles are moved or rearranged
in a particular manner close to each other to avoid
any trapped air or voids. It increases the load bear-
ing capacity, decreases water seepage, prevents soil
settlement, reduces swelling, contraction of the soil
and prevents frost damage. It is ideal for compaction
of interlocking paving stones, trenches, landscaping
and maintenance.
m ATTENTION!
The compactor is not intended to be used on co-
hesive soils such clay or hard surfaces like con-
crete.
12.12.2019 07:33:38 12.12.2019 07:33:38