Maintenance - Chicco STYLEGO up Bedienungsanleitung

inside.
• The carrycot is not designed for
children to sleep in for long periods
of time: this product is not a substi-
tute for a cot.
• Air the carrycot after prolonged use.
• Before lifting or transporting the
carrycot, the base needs to be ad-
justed to the lowest position.
• In the carrycot, your child's head
must never be lower than their
body.
• WARNING: The restraint system
must be used only when transport-
ing your child in the car.
• WARNING: The restraint system
must be removed when the prod-
uct is used outside the car.
• Keep the product out of reach of
children when it is not being used.
TIPS FOR CLEANING AND MAINTENANCE
This product requires periodical maintenance. Cleaning
and maintenance operations must be performed exclu-
sively by an adult.
CLEANING
Clean the fabric parts using a wet sponge and neutral soap.
Periodically wipe the plastic parts clean with a soft damp
cloth. Always dry the metal parts to prevent the formation
of rust if the stroller has come into contact with water.
WASHING
The external/internal lining of the carrycot and the mat-
tress are removable and washable; to remove them, please
refer to the paragraph REMOVING THE CARRYCOT LINING.
Carefully follow the washing instructions on the label. The
washing symbols and relative meanings are listed below:
Handwash in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean

MAINTENANCE

To prevent the formation of rust, always dry metal parts. Do
not submerge the carrycot in water. Periodically clean plas-
tic parts with a damp cloth. To avoid friction, ensure that
the locking devices of the carrycot and pram are free from
dust and sand. Do not leave the product exposed to the
sun for a long period of time; the fabrics may discolour. If
necessary, lubricate with dry silicone lubricant. Do not use
solvents or abrasive cleaning products.
CARRYCOT FEATURES
The carrycot is comprehensive of the following compo-
nents: fabric lining, hood, cover, detachable mattress, com-
fort kit (two shoulder straps and a crotch strap), and detach-
able kit for car transportation.
1. The carrycot is supplied with the fabric lining already fit-
ted (Fig. 1).
HOODS
The carrycot is equipped with a sun canopy and windshield
that can be adjusted to various positions, while the upper
part features an opening to reach the carrying handle.
2. To fit the hood on the carrycot, lift the carrying handle of
the carrycot into vertical position (Fig. 2A), place the hood
on the handle and fasten the four snap buttons on the
edge of the hood on the matching buttons in the fabric of
the carrycot (Fig. 2B).
3. To fasten the hood to the handle, wrap of the fabric of the
hood around it, fasten the two snap buttons on the joint
(Fig. 3A) and close the Velcro straps around the handle
(Fig. 3B). To complete the operation, pull the edge of the
hood fabric beyond the handle (Fig. 3C).
REAR OPENING
4. To ensure proper ventilation, the hood features a rear
opening; to open it, just fold the flap on the upper part
of the hood (Fig. 4).
HOOD
5. The internal part of the hood features a fabric ring that
allows you to hang soft toys (Fig. 5).
COVER
6. To secure the cover, fasten the two snap buttons locat-
ed on the sides of the carrycot (Fig.6) and complete the
operation by inserting the elastic strap around the pin
located in the foot zone (Fig. 6A). Then fasten the fabric
flap of the cover to the hood using the two snap buttons
(Fig. 6C). To ensure the utmost safety of your child, you
can use the fabric flap in vertical position fastening it to
the relevant holes (Fig. 6C).
ADJUSTABLE BACKREST - COMFORT SYSTEM
7. The carrycot backrest can be adjusted gradually.
To incline or recline the backrest, use the wheel located on
the outer part of the carrycot near the baby's feet (Fig. 7).
CARRYING HANDLE
8. The carrycot features a comfortable carry handle that can
be adjusted in three positions (Fig. 8):
A) Transport
B) Middle
C) Rest
9. To put the handle in the vertical position, grasp it in the
centre and pull it up until you hear a click (Fig. 9 A); to re-
turn the handle to middle position, press the two buttons
on the joint of the handle at the same time; to go from
the middle position to the rest position, repeat the step
13