Troubleshooting Guide; Warranty; Technical Data; Vibration Value - Kärcher CNS 18-30 Battery Originalbetriebsanleitung

6. If necessary, mount the chain tensioner on the new
guide rail.
Illustration AG
7. Fit the new chain on the guide rail. Observe the di-
rection of rotation of the chain.
Illustration C
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device does not start
up
The device stops during
operation

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Working voltage of the battery
No-load chain speed
Chain oil tank volume
Determined values in acc. with EN 60745-1, EN
60745-2-13
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
wA
Uncertainty K
WA
Front handle hand-arm vibration
value
Rear handle hand-arm vibration
value
Uncertainty K
Dimensions and weights
Length x width x height
Guide rail length
Cutting length
Chain pitch
Weight (without battery pack)
Subject to technical modifications.

Troubleshooting guide

Cause
Battery pack is empty
Battery pack is defective.
Battery pack is not inserted correctly.
The battery has overheated
Motor has overheated
V 18
m/s 10
ml 200
dB(A) 87,9
dB(A) 3,0
dB(A) 98,9
dB(A) 1,4
2
m/s 3,5
2
m/s 5,2
2
m/s 1,5
mm 735 x
230 x
247
mm 300
mm 250
in (mm) 0,375
(9,525)
kg 3,2
8. Place the chain around the sprocket and insert the
guide rail.
Illustration D
9. Fit the bar cover and tighten the chain tensioner
knob.
Illustration E
10. Adjust the chain tension (see Chapter Adjusting the
chain tension).
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Charge the battery pack.
 Replace the battery pack.
 Push the battery pack into the mounting
until it latches into place.
 Stop working and allow the battery to cool
down to normal battery temperature.
 Stop working and allow the motor to cool
down.

Vibration value

WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Device with a hand-arm
vibration value > 2.5 m/s² (see
chapter Technical Data in the
operating instructions)
CAUTION ● Uninterrupted
use of the device for several
hours can lead to numbness.
● Wear warm gloves to protect
your hands. ● Take regular
breaks from work.

EU Declaration of Conformity

We hereby declare that the machine described below
complies with the relevant basic safety and health re-
quirements in the EU Directives, both in its basic design
and construction as well as in the version placed in cir-
culation by us. This declaration is invalidated by any
changes made to the machine that are not approved by
us.
Product: Cordless chainsaw
Type: 1.444-00x.x
Currently applicable EU Directives
2014/30/EU
2006/42/EC (+2009/127/EC)
2011/65/EU
English 41