Herunterladen Diese Seite drucken

Storage; Care And Service - Kärcher CNS 18-30 Battery Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für CNS 18-30 Battery:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
2. Push the hand guard/chain brake lever towards the
guide rail.
Illustration N
The chain brake is locked.
3. Install the bar scabbard.
Illustration F
4. Only carry the device by the handle and with the
guide rail facing to the rear.
5. Empty the chain oil tank when transporting over
longer distances.
a Remove the chain oil tank cap.
Illustration G
b Fill the chain lubricating oil into a suitable contain-
er.
c Tighten the chain oil tank cap.
6. Secure the device against slipping and tipping over
when transporting in vehicles.

Storage

CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
CAUTION
Uncontrolled startup
Incision injuries
Remove the battery pack from the device before stor-
age.
Store the device only with the blade guard fitted.
1. Remove the battery pack (see chapter Removing
the battery pack).
2. Push the hand guard/chain brake lever towards the
guide rail.
Illustration N
The chain brake is locked.
3. Install the bar scabbard.
Illustration F
4. Empty the chain oil tank.
a Remove the chain oil tank cap.
Illustration G
b Fill the chain lubricating oil into a suitable contain-
er.
c Tighten the chain oil tank cap.
5. If the device is to be stored for more than one month,
oil the chain to prevent rust.
6. Store the device in a dry, well ventilated location.
Keep away from corrosive substances such as gar-
den chemicals and defrosting salt. Do not store the
device outdoors.

Care and service

CAUTION
Uncontrolled startup
Incision injuries
Remove the battery from the device before all work on
the device.
CAUTION
Sharp chain
Incision injuries
Wear protective gloves when working on the chain.
Cleaning the device
1. Remove the battery pack (see Chapter Removing
the battery pack).
2. Use a brush to clean the chain of cutting residue and
dirt.
Illustration AA
3. Clean the housing and handles with a soft, dry cloth.
40
4. Check the function of the chain brake after every
cleaning (see Chapter Checking the functionality of
the chain brake).
Maintenance intervals
The following activities must be carried out before every
use:
 Check the filling level of the chain oil, top up the
chain oil if necessary (see Chapter Filling the chain
oil tank).
 Check the chain tension (see Chapter Checking the
chain tension).
 Check the chain for sufficient sharpness, if neces-
sary replace the chain (see Chapter Replacing the
chain and guide rail).
 Check the device for damage.
 Check all pins, nuts and screws for tightness.
 Check the function of the chain brake (see Chapter
Checking the functionality of the chain brake).
Every 5 operating hours
 Check the function of the chain brake every 5 oper-
ating hours (see Chapter Checking the functionality
of the chain brake).
Maintenance work
Checking the functionality of the chain brake
1. Switch the device on.
2. While the device is running, turn your hand on the
front handle so that the hand guard/chain brake le-
ver is pressed towards the guide rail with the back of
your hand.
The chain brake is locked.
The chain must come to a standstill.
3. Pull the hand guard/chain brake lever in the direc-
tion of the handle.
The chain must release.
Adjusting the chain tension
1. Remove the battery pack (see chapter Removing
the battery pack).
2. Loosen the chain tensioner knob.
Illustration AB
3. Adjust the chain tension with the ring.
Illustration AC
4. Check the chain tension.
Illustration J
The distance between the guide rail and the chain
must be 3-4 mm.
5. Tighten the chain tensioner knob.
Replacing the chain and guide rail
CAUTION
Sharp chain
Incision injuries
Wear protective gloves when working on the chain.
1. Remove the battery pack (see chapter Removing
the battery pack).
2. Release the chain tensioner knob and remove the
bar cover.
Illustration AD
3. Remove the guide rail with the chain tensioner.
Illustration AE
4. Remove the chain tensioner if the guide rail is to be
replaced.
Illustration AF
5. Dispose of the old chain and, if necessary, the guide
rail properly.
English
Before every use

Werbung

loading