Specifications - Interlogix ATS1210 Installationsanleitung

ABCT (item 2):
•
T: Set switch T on if this device is the last device on the
system databus. For more details see the ATS control
panel installation guide.
•
A, C: Not in use
• B: ON — ATS1811 8-way relay card or ATS1820 16-way
open collector card connected to J4. OFF — no ATS1811
or ATS1820 connected to J4. Use this setting also if an
ATS1810 is connected to J4.
Zone numbering
A 4/8-zones DGP can have four or eight zones connected to it.
There are 16 zones allocated to every DGP address. Only
zones 1 to 4 or 1 to 8 can be used when an
ATS1210/1211/1220 is allocated a DGP number. Zones not
available (5–16 or 8–16) should be programmed as type 0
(zone disabled) in the Zone database.
Control panel 1–16
DGP1 17–32
DGP2 33–48
DGP3 49–64
DGP4 65–80
DGP5 81–96
DGP6 97–112
DGP7 113–128
Note: The ATS1210/1211/1220 cannot be expanded to
provide additional zones.
LEDs
•
RX: LED flashes to indicate polling data is being received
on the system databus from the ATS control panel. If the
LED does not flash the control panel is not operational or
the databus is faulty (usually cabling).
•
TX: LED flashes to indicate the DGP is replying to polling
from the ATS control panel. If the RX LED flashes but the
TX LED does not, it indicates that the DGP is not
programmed to be polled in the control panel or that it is
addressed incorrectly.

Specifications

Supply voltage
Maximum operating current
Dimensions (H x W) (size B board)
Dimensions metal housing (H x W x L)
Dimensions plastic housing (H x W x L)
Operating temperature
IP rating
Relative humidity
2 / 18
DGP8 129–144
DGP9 145–160
DGP10 161–176
DGP11 177–192
DGP12 193–208
DGP13 209–224
DGP14 225–240
DGP15 241–256
10.5 to 13.8 V
(12 V nom.)
53 mA
90 x 80 mm
165 x 125 x 36 mm
86 x 125 x 36 mm
0 to +50°C
IP30
<95% noncondensing
Regulatory information
Manufacturer PLACED ON THE MARKET BY:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092,
USA
AUTHORIZED EU REPRESENTATIVE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings THESE PRODUCTS ARE INTENDED FOR
and disclaimers SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Certification
European Union UTC Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu
DA: Installationsvejledning
Montering af enheden
Monter 4/8-DGP printet i et ATS kabinet, der understøtter BB-
print-format.
Tilslutninger
J1
• KOMMUNIKATION +, −: 12 V dc forsyning. Det anbefales
at bruge en ekstern strømforsyning, hvis afstanden
mellem en ATS1220 og den nærmeste centarl eller DGP
overstiger 100 meter.
• KOMMUNIKATION D+, D−: Positiv og negativ
datatilslutning på databussen. Enheder kan placeres op til
1,5 km fra 4-elevators DGP'et eller ATS-centralen, dog
afhængigt at hvilket kabeltype der anvendes. I
or scan the QR code.
P/N 1052529 • REV C • ISS 02JUL19