Specifications - Interlogix ATS1170 Installationsanleitung

D0 Data connection to reader.
D1 Data connection to reader.
L2 Open collector output to control reader LED.
L1 Open collector output to control reader LED.
BZ Open collector output to control reader beeper if fitted.

Specifications

Power supply
Current consumption without reader
Reader power output (depending on
RDR link setting)
Reader output current for 2 s
Constant
Relay contact ratings:
Max. current
Max. voltage
Dimensions (H x W) (size B board)
Cable
Regulatory information
Manufacturer PLACED ON THE MARKET BY:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092,
USA
AUTHORIZED EU REPRESENTATIVE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings THESE PRODUCTS ARE INTENDED FOR
and disclaimers SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Certification
UTC Fire & Security hereby declares that this
device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com
2 / 16
12 V
45 mA max.
+5V to +12 V
5V max. at 100 mA
5V at 75 mA
0 to 30 V at 1 A
48 V at 300 mA
80 x 52 mm
Cat. 5 UTP data cable.
Max. length 50 meters
or scan the QR code.
For customer support, seewww.utcfssecurityproducts.eu
DA: Installationsvejledning
Montering
Printkortet ATS1170 kan monteres i alle eksisterende
centralkabinetter som støtter B-modul print B.
Dip-switch for RAS
Se figur, punkt 1.
Adressering: Dip-Switch 1 til 4 bruges til at indstille RAS-
adressen. Se også iinstallationsmanualen for ATS-
Centralenhenden.
DIP-switch
Se figur, punkt 2.
ON: Enheden er den sisdte fysiske enhed på databussen (term).
T
OFF: Enheden er IKKE den siste fysiske enhed på databussen.
A ON: Aktiver offline programmeringsmodus.
OFF: Deaktiver offline-programmering. Brug denne indstillingen
for normal drift.
B ON: Aktiver standard bank- og kreditkort med magnetstripe.
OFF: Aktiver magnetkort i ATS-format.
ON: Magnetstripelæser bruges.
C
OFF: Wiegand-læser bruges.
Tilkobling til ATS-databuss (system eller
lokalt) og jording
Se i installationsmanualen for ATS-centralenheden.
Tilslutninger J2 og J3
J2: PWR 12 VDC indgang til forsyning samt Data positiv og
negativ til kommunikation via databussen.
J3: Relæ til el-lås (NO/C/NC). Dette relæ vil være aktiveret i
den tid døren er låst op, samtidig vil udgangen L1 eller L2
pulse. Se i programmeringsmanualen for ATS centralen om
denne type RAS udgangskontrolgruppe
(programmeringsmenu 3).
LED's
RX: LED blinker for at angive, at der modtages polling via
databussen fra ATS-central. Hvis LED'en ikke blinker, er
centralenheden ikke driftsklar, eller der er fejl på databussen
(oftest kabel- eller monterings-fejl).
TX: LED blinker for at angive, at RAS'en reagerer på polling fra
ATS-central. Hvis RX LED'en blinker, men TX LED'en ikke
blinker, er RAS'en ikke programmeret til at polles i
centralenheden eller RAS'en har forkert adresse.
Se i installationsmanualen for ATS-centralenhed for detaljer.
P/N MAINST-ATS1170 (ML) • REV D • ISS 23MAY19