Putting Into Operation - Bosch 0 607 352 109 Bedienungsanleitung

bu_3609929977_t.fm Seite 10 Montag, 11. Oktober 2004 12:17 12
Removal
Caution! Accessories can become hot when the
tool is operated for a longer time. Use protective
gloves.
17
14
10
8
9
Subsequently, you can pull the abrasive, cut-off, or
wire brushing wheel, as well as, in the case of angle
grinders with M14 spindle thread, the inner flange 11,
from the tool spindle. In the case of angle grinders
with 5/8"–11 UNC spindle thread, the inner flange
must be unscrewed from the spindle thread.
Sanding with the Rubber Backing Pad
Installation
8
7
6
17
14
5
the pin spanner wrench 8 to screw it securely onto the
tool spindle, while you apply a counterforce on the
wrench flats of the tool spindle 14 with the open end
wrench 17. Take care that the pad nut for flat discs 7
is screwed into the depression of the rubber backing
plate, so that it does not interfere with sanding and so
that the sanding disc is held firmly in place.
3 609 929 977 • (04.10) T
Use exclusively sanding discs that fit the rubber
backing pad!
Removal
Caution! Accessories can become hot when the
In order to remove the
tool is operated for a longer time. Use protective
abrasive, cut-off, or
gloves.
wire brushing wheel
10, hold the tool spin-
Use the pin spanner wrench 8 to unscrew the pad nut
dle 14 firmly on the
for flat discs 7 from the tool spindle 14, while you apply
wrench flats with the
a counterforce on the wrench flats 15 of the tool spin-
open end wrench 17.
dle with the open end wrench 17.
Subsequently, you can pull the sanding disc 6 and the
rubber backing pad 5 from the spindle.
You can unscrew a
stuck outer flange nut

Putting into Operation

9 from the tool spindle
The air tool operates optimally with a pressure of
by using the pin span-
6.3 bar (91 psi) measured at the air inlet with the tool
ner wrench 8, while
running.
you apply a counter-
force on the wrench
If, at a higher nominal pressure, the installed accessory
flats of the tool spindle rotates more rapidly than permitted, it may be de-
with the open end stroyed and fragmenting parts may injure you.
wrench.
Remove adjusting keys before turning the tool
on. A key that is left attached to a rotating part of the
tool may result in personal injury.
After inspecting and installing an accessory, po-
sition yourself and bystanders away from the
plane of the rotating accessory and run the air
tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
Switching On/Off
If the tool does not run – for example, after not being
After you have mount-
used for a prolonged time – disconnect the air supply
ed the hand guard 4
and turn the motor repeatedly using an open-end
together with the aux-
wrench 17 on the wrench flats 15 of the tool spindle.
iliary handle 3 (see
This eliminates adhesion forces.
Mounting the Protec-
tive Device), place the
Type 0 607 352 109/... 112/... 117/... 119
rubber backing pad 5
Locking switch
on the tool spindle 14.
Then lay the sanding
disc 6 on the rubber
backing pad 5. Fix the
sanding disc 6 in
place on the rubber
backing pad by plac-
ing the pad nut for flat
Type 0 607 352 113/... 114/... 118/... 120
discs 7 on the tool
Deadman switch
spindle 14 and using
English–10
Switching on:
18
Slide the on/off switch 18 forward.
Switching off:
Slide the on/off switch 18 backward
to release the locking and to switch
off the tool.
Switching on:
18
Press the on/off switch 18 and keep
it pressed during the working oper-
ation.
Switching off:
Release the on/off switch 18.