List Of Parts - Spokey LEGANES II Bedienungsanleitung

LIST OF PARTS

Diagram – p. 34
NO. Description
1 Circular End Cap
2 Internal Handle
3 Pulse Sensor
4 End Cap
5 Bolt M8x30
6 Bolt
7 Washer
Washer Ø8
8
9 End Cap
10 Pulse Sensor Wire
11 Bolt
12 Washer
13 Tension Adjustment Knob
14 Handle Post
15 Cable
16 End Cap
17 Handles
18 Foam
19 Foam
20 Square End Cap S13
21 Bolt M8x16
Bolt M5x12x Ø10
22
Washer d8x Ø32
23
24 Small Bushing
25 Bolt M8x40x20
Washer d8x Ø20
26
27 Nut M8Xh16
28 Small Circular Bushing
29 Washer
30 Long Small Bushing
31 Middle Part of the Handle
32 Bolt
33 Small Bushing
34 Small Bushing of the Shaft
Washer d8x Ø16x1.5
35
36 Nut M8xH7
37 Transport Wheels
38 Bolt
39 Bolt M8x60x20
INSTALLATION INSTRUCTIONS (Drawings – p. 37)
STEP 1. Attach the front and rear stabilizer (40), (63) onto the main frame
(67) with the bolts (39), washers (41) and nuts (27).
STEP 2.
1. Connect the cable (13) and (65);
2. Connect the cable (15) with the cable (64).
3. Attach the handle post (14) onto the main frame (67) with the bolts (66)
and washers (41).
STEP 3.
1. Attach the left and right part of the handles (31L/R) onto the handle posts
(14) with the bolts (21), washers (8) and washers (23).
2. Attach the common bar of the pedals (58) onto the main frame (67) with
the crank bolts (55L/R), wave washer (56), and then with the nuts (60L/R)
and washers (59).
Moving the device
Raise the trainer carefully onto its transport wheels (Picture – p. 41) and move to a given place, holding it on both sides.
Resistance adjustment
The Resistance adjustment function allows to change resistance on the
pedals. High resistance requires larger effort while pedalling, whereas the
low one decreases the effort. Force of resistance is regulated by a knob
placed on the handlebar post. In order to decrease resistance, adjustment
ASSEMBLY, SETUP AND MAINTENANCE
QTY NO.
2 40 Front Stabilizer
Washer d8x Ø20
1 41
2 42 Meter
1 43 Bolt
2 44 Skid Coupler with Arm
2 45 End Cap
2 46 Pedal Base
4 47 Washer
1 48 Nut
1 49 N/A
1 50 Pedal L+R
1 51 Bolt
1 52 Foot Metal Bushing
1 53 Washer
1 54 End Cap
Crank Bolts Ø16x89x23x1/2
2 55
Wave Washer d17x Ø25x0.3
1 pair 56
2 57 Foot Metal Bushing
2 58 Pedals Common Bar
Washer Ø1/2"
6 59
2 60 Nut 1/2x20xH8
2 61 End Cap M8x16
2 62 Rear Stabilizer End Caps
4 63 Rear Stabilizer
6 64 Motor Cable (Tension Adjustment Cord)
2 65 Sensor Cable
6 66 Bolt M8x16
2 67 Main Frame
2 68 Allen Key s8
2 69 Allen Key s6
2 70 Wrench S13-14-15
2 71 Wrench S17-18-19
2 72 Bolt
4 73 Washer
6 74 Bolt
6 75 Board with Bushing for Crank
2 76 Bearings
2 77 Bearing Seat
4 78 Flywheel Shaft
Description QTY
1
8
1
3
2
4
1 pair
2
4
1 pair
2
4
2
2
1 pair
2
4
1 pair
2
1 pair
2
2
1
1
1
4
1
1
1
1
1
3
3
5
2
4
2
1
3. Apply the end caps (20), (54) and (61) in proper places.
STEP 4. Attach the pedals (51L/R) onto the base (46) with the bolts (25),
washers (35) and nuts (36).
STEP 5. Attach the handles (17L/R) onto the middle part of the handles
(31L/R) with the bolts (25), washers (26) and nuts (27).
STEP 6.
1. Attach the middle handle (2) onto the post (14) with the bolts (5) and
washers (8).
2. Finish the middle handle (2) with the end cap (4).
STEP 7.
1. Connect the meter (42) to the post (14) with the bolts (22).
2. Insert the wire (10) into the hole located in the meter (42).
knob should be turned towards the "1" number whereas so as to increase
resistance, the knob should be turned towards the "8" number.
In order to achieve a satisfying effect, resistance level should be set during
a training.
6
NO. Description
79 Flywheel
80 Bolt
81 Free-wheel
82 Washer
83 Bolt
84 Washer
85 Free-wheel Frame
86 Nut
87 Spring
88 Crank Cover
89 Rotation Board
90 Bolt
91 Bolt
92 Cover
93 Nut
94 Washer
95 Bushing
96 Bushing Crate
97 Bushing Stand
98 Bolt
99 Nut
100 Bolt
101 Collar
102 Washer
103 Circular Magnet
104 Pulley
105 Crank
106 Belt
107 Magnet Seat
108 Square Magnet
109 Bolt
110 Washer
111 Washer
112 Washer
113 Bolt
114 Puller
115 Magnet Board
116 Flywheel Shaft
117 End Cap
QTY
1
1
1
1
1
1
1
1
1
2
2
4
7
2
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
4
2
2
2
2
5
1
1
1
1