Residual Risk - Ryobi RBC430SESD Bedienungsanleitung

TRIMMER SAFETY WARNINGS
■ Replace string head if cracked, chipped, or damaged
in any way. Be sure the string head or blade is properly
installed and securely fastened. Failure to do so can
cause serious injury.
■ Avoid using on wet grass.
■ Do not walk backwards when using the product.
■ Walk, never run.
■ The small blade fitted to the cutting attachment guard
is designed to trim the new extended line to the correct
length for safe and optimum performance. It is very
sharp; do not touch it, particularly when cleaning the
product.
■ Always ensure that ventilation openings are kept clear
of debris.
■ Before use and after any impact, check that there
are no damaged parts. Examine the cutting means
for signs of cracking or other damage. A defective
switch or any part that is damaged should be properly
repaired or replaced by an authorised service facility.
■ Make sure the head attachment is properly installed
and securely fastened.
■ Make sure all guards, deflectors and handles are
properly and securely attached.
■ Do not modify the product in any way. This may
increase the risk of injury to yourself or others.
■ Use only the manufacturer's replacement line in the
cutting head. Do not use any other cutting attachment.
■ Never operate unit without the cutting attachment
guard in place and in good condition.
■ Maintain a firm grip on both handles while trimming.
Keep string head below waist level. Never cut with
the string head located over 76 cm or more above the
ground.
BRUSHCUTTER SAFETY WARNINGS
■ In addition to the above rules, these additional
instructions are appropriate when using the machine
in brush cutter mode.
■ Use heavy gloves when installing or removing blades.
The blades are sharp.
■ Do not attempt to touch or stop the blade when it is
rotating.
■ A moving blade can cause severe injury. Maintain
proper control of the machine with both hands until the
blade has completely stopped rotating.
■ Replace any blade that has been damaged. Always
make sure blade is installed correctly and securely
fastened before each use.
■ Use only the manufacturer's replacement Tri-Arc™
blade. Do not use any other cutting attachment.
■ Never cut any material over 13 mm diameter.
English (Original instructions)
■ Your brushcutter is fitted with a harness. Carefully
■ Identify the Quick Release mechanism and practice
■ Cover the blade with the blade protector before storing
■ Exercise extreme caution when using the blade with
■ For cutting ease and safety, approach the weeds

RESIDUAL RISK

Even when the machine is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and
the operator should pay special attention to avoid the
following:
■ Contact with cutting means. Ensure that the blade
■ Injury caused by vibration. Always use the right tool for
■ Exposure to noise can cause hearing injury. Wear ear
■ Eye injury due to flying debris. Wear eye protection
■ Kickback can occur when using the brushcutter.
■ Risk of falling objects: During brush cutting, wear head
17
adjust the harness to fit comfortably and help to
support the weight of the machine at your right side.
using it before you start using the machine. Its
correct use may prevent serious injury in case of
an emergency. Never wear additional clothing over
the harness or otherwise restrict access to the quick
release mechanism.
the unit, or during transportation. Always remove the
blade protector before using the unit. If not removed,
the blade protector could become a thrown object as
the blade begins to turn.
this unit. Blade thrust is the reaction that may occur
when the spinning blade contacts anything it cannot
cut. This contact may cause the blade to stop for an
instant, and suddenly "thrust" the unit away from the
object that was hit. This reaction can be violent enough
to cause the operator to lose control of the unit. Blade
thrust may occur without warning if the blade snags,
stalls, or binds. This is more likely to occur in areas
there it is difficult to see the material being cut.
being cut from the right to the left. In the event an
unexpected object or woody stock is encountered, this
practice could minimise the blade thrust reaction. Both
hands must be used at all times to control this product.
protectors are fitted when the machine is not in use.
Keep hands and feet away from the blades at all times
the job, use designated handles and restrict working
time and exposure.
protection and limit exposure
at all times.
Ensure proper control by using both hands on the
designated handles. Read and follow the directions
elsewhere in this manual to help reduce the risk of
kickback.
protection if there is any risk of falling objects.