General Power Tool Safety Warnings - Stiga T 1.0 EJ Gebrauchsanweisung

SAFETY WARNINGS
7) Keep extension cords away from cutting ele-
ments.
8) Power the machine using a residual current de-
vice (RCD Residual Current Device) with max. 30
mA tripping current.
• How to use the electric grass trimmer
When using the machine, always use caution and take on
a firm and well-balanced position.
– Where possible, avoid working on wet, slippery ground
or in any case on uneven or steep ground that does not
guarantee stability for the operator.
– Never run, but walk carefully paying attention to the lay
of the land and any eventual obstacles.
– Assess the potential risks of the ground to be mown
and take all necessary precautions to en sure your own
safety, especially on slopes or on bumpy, slippery or
unstable ground.
– Work along the contour on slopes, never when walking
up or down and always keep downhill of the cutter.
Do not use the machine if you are unable to hold it with
both hands or keep it steady on your legs while working.
The machine must never be used by more than one per-
son.
Never use the machine if the user is tired or unwell, or has
taken medicine, drugs, alcohol or any substances which
may slow his reflexes and compromise his judgement.
• Techniques for using the electric grass
trimmer
Always observe the safety regulations and use the most
suitable cutting techniques (see chapter 7 for in structions
and examples).
• Handling the electric grass trimmer safety
Whenever the machine is to be handled or transpor ted
you must:
– turn off the motor, wait for the cutting device to stop and
unplug the machine from the mains;
– only hold the machine using the handgrips and position
the cutting device in the opposite direction to that used
during operation.
When using a vehicle to transport the machine, position
it so that it can cause no danger to persons and fasten
it firmly.
• Recommendations for first-time users
Before tackling a mowing job for the first time it is advis-
able to gain the necessary familiarity with the machine
and the most suitable cutting techniques, finding out how
to firmly grip the machine and making the movements
required by the job.
GENERAL POWER TOOL
SAFETY WARNINGS
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive at-
mospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Ne-
ver modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodified plugs and matching outlets will re duce risk
of electric shock.
b) Avoid body contact with earthed or grounded sur-
faces, such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
d) Do not use the cord improperly. Never use the
cord for carrying, pulling or unplugging the po wer
tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or en tangled cords in-
crease the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Using
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Using an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turn-
ing the power tool on. A wrench or a key left at-
tached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
5
EN