Herunterladen Inhalt Inhalt
Teilen
Diese Seite drucken
Honda EU30i Bedienungsanleitung
  1. Anleitungen
  2. Marken
  3. Honda Anleitungen
  4. Generatoren
  5. EU30i
  6. Bedienungsanleitung

Honda EU30i Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für EU30i:
Inhaltsverzeichnis

Werbung

Quicklinks

Diese Anleitung herunterladen
11/05/10 11:27:13 32Z28610_001
The''e-SPEC''mark symbolizes environmentally
responsible technologies applied to Honda power
equipment, which contains our wish to ''preserve
nature for generations to come.''
Honda
EU30i
OWNER'S MANUAL
Original instructions
MANUEL DE L'UTILISATEUR
Notice originale
BEDIENUNGSANLEITUNG
Originalbetriebsanleitung
MANUAL DE EXPLICACIONES
Manual original

Werbung

Inhaltsverzeichnis
loading

Verwandte Anleitungen für Honda EU30i

Inhaltszusammenfassung für Honda EU30i

  • Seite 1 11/05/10 11:27:13 32Z28610_001 Honda EU30i OWNER’S MANUAL Original instructions MANUEL DE L’UTILISATEUR Notice originale BEDIENUNGSANLEITUNG Originalbetriebsanleitung MANUAL DE EXPLICACIONES Manual original The‘‘e-SPEC’’mark symbolizes environmentally responsible technologies applied to Honda power equipment, which contains our wish to ‘‘preserve nature for generations to come.’’...
  • Seite 2 11/05/10 11:27:15 32Z28610_002...
  • Seite 3 All information in this publication is based on the latest product information available at the time of approval for printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation.

  • Seite 4: Inhaltsverzeichnis

    ............... 50 11. SPECIFICATIONS ................53 12. WIRING DIAGRAM ................55 RECEPTACLE ..................56 MAJOR Honda DISTRIBUTOR ADDRESSES ....Inside back cover ‘‘ EC Declaration of Conformity ’’ CONTENT OUTLINE ..Inside back cover...

  • Seite 5: Important Safety Information

    11/05/10 11:27:36 32Z28610_005 SAFETY INSTRUCTIONS IMPORTANT SAFETY INFORMATION Honda generators are designed for use with electrical equipment that has suitable power requirements. Other uses can result in injury to the operator or damage to the generator and other property. Most injuries or property damage can be prevented if you follow all instructions in this manual and on the generator.
  • Seite 6 11/05/10 11:27:43 32Z28610_006 Carbon Monoxide Hazards Exhaust contains poisonous carbon monoxide, a colorless, odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. If you run the generator in an area that is confined, or even partially enclosed area, the air you breathe could contain a dangerous amount of exhaust gas.
  • Seite 7 11/05/10 11:27:50 32Z28610_007 Fire and Burn Hazards Do not use the generator in areas with a high risk of fire. The exhaust system gets hot enough to ignite some materials. − Keep the generator at least 1 meter (3 feet) away from buildings and other equipment during operation.
  • Seite 8 Do not throw it in the trash or pour it on the ground. An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. Contact your Honda servicing dealer for a replacement.

  • Seite 9: Safety Label Locations

    These labels warn you of potential hazards that can cause serious injury. Read the labels and safety notes and precautions described in this manual carefully. If a label comes off or becomes hard to read, contact your Honda dealer for a replacement. For European model: G/G8, GW, F, IT types READ OWNER’S MANUAL...
  • Seite 10 11/05/10 11:28:09 32Z28610_010 Honda generator is designed to give safe and dependable service if operated according to instructions. Read and understand the Owner’s Manual before operating the generator. Failure to do so could result in personal injury or equipment damage.
  • Seite 11 11/05/10 11:28:15 32Z28610_011 Gasoline is highly flammable and explosive. Turn the engine off and let it cool before refueling. Connect and remove the receptacle box for parallel operation with the engine stopped. For single operation, the receptacle box for parallel operation must be removed. A hot exhaust system can cause serious burns.
  • Seite 12 11/05/10 11:28:25 32Z28610_012 For U types For U type...

  • Seite 13: Ce Mark And Noise Label Locations

    11/05/10 11:28:33 32Z28610_013 CE mark and noise label locations For European model: G/G8, GW, F, IT types NOISE LABEL CE MARK Performance class Quality class IP code Dry mass Name and address of Year of manufacture Manufacturer and address authorized representative...

  • Seite 14: Component Identification

    11/05/10 11:28:39 32Z28610_014 COMPONENT IDENTIFICATION FUEL TANK CAP VENT LEVER FUEL TANK CAP STARTER GRIP FOLDING HANDLE SPARK PLUG MAINTENANCE COVER AIR CLEANER COVER MUFFLER FRAME SERIAL NUMBER OIL MAINTENANCE COVER Record the frame serial number in the space below. You will need this serial number when ordering parts.

  • Seite 15: Control Panel

    11/05/10 11:28:43 32Z28610_015 CONTROL PANEL G/G8, GW, F types OVERLOAD INDICATOR AC RECEPTACLES OIL ALERT INDICATOR OUTPUT INDICATOR PARALLEL OPERATION SOCKETS AC CIRCUIT PROTECTOR (Except RG type) DC RECEPTACLE DC CIRCUIT PROTECTOR GROUND TERMINAL AC CIRCUIT PROTECTOR (Except RG type) ENGINE SWITCH ECO THROTTLE SWITCH IT type...
  • Seite 16 11/05/10 11:28:47 32Z28610_016 U type AC RECEPTACLES OVERLOAD INDICATOR OIL ALERT INDICATOR OUTPUT INDICATOR PARALLEL OPERATION SOCKETS DC RECEPTACLE DC CIRCUIT PROTECTOR GROUND TERMINAL ENGINE SWITCH ECO THROTTLE SWITCH...
  • Seite 17 11/05/10 11:28:53 32Z28610_017 Eco Throttle ECO: Engine speed is kept at idle automatically when the electrical appliance is disconnected and it returns to the proper speed by the electrical load when electrical appliance is connected. This position is recommended to minimize the fuel consumption while in operation. Eco Throttle system does not operate sufficiently if the electrical appliance requires the momentary electric power.

  • Seite 18: Pre-Operation Check

    11/05/10 11:29:00 32Z28610_018 PRE-OPERATION CHECK Be sure to check the generator on a level surface with the engine stopped. Check the engine oil level. Using non detergent oil or 2-stroke engine oil could shorten the engine’s service life. Recommended oil Use 4-stroke motor oil that meets or exceeds the requirements for API service category SE or later (or equivalent).
  • Seite 19 11/05/10 11:29:06 32Z28610_019 Open the oil maintenance cover. Remove the oil filler cap, and wipe the dipstick with a clean rag. Check the oil level by inserting the dipstick in the oil filler hole without screwing it in. If the oil level is below the end of the dipstick, refill with recommended oil up to the top of the oil filler neck.

  • Seite 20: Fuel Tank Cap

    11/05/10 11:29:15 32Z28610_020 Check the fuel level. If the fuel level is low, refuel the fuel tank until the level as specified. After refueling, tighten the fuel tank cap securely. Use automotive unleaded gasoline with a Research Octane Number of 91 or higher (a Pump Octane Number of 86 or higher).
  • Seite 21 Gasolines Containing Alcohol If you decide to use a gasoline containing alcohol (gasohol), be sure its octane rating is at least as high as that recommended by Honda. There are two types of ‘‘gasohol’’: one containing ethanol, and the other containing methanol.
  • Seite 22 11/05/10 11:29:30 32Z28610_022 Check the air cleaner. Check the air cleaner elements to be sure it is clean and in good condition. Loosen the air cleaner cover screw, and remove the air cleaner cover. Remove the main and outer elements from the air cleaner case, and check the elements.
  • Seite 23 11/05/10 11:29:35 32Z28610_023 Make sure that the rubber seal is set in the groove of the air cleaner case. Replace the rubber seal if it is damaged. Reinstall the main and outer elements. Put the outer element between the upper and lower ribs. AIR CLEANER CASE RUBBER SEAL RIBS...

  • Seite 24: Starting The Engine

    11/05/10 11:29:42 32Z28610_024 STARTING THE ENGINE Before starting the engine disconnect any load from the AC receptacle. Turn the fuel tank cap vent lever fully clockwise to the ON position. Turn the fuel tank cap vent lever to the OFF position when transporting the generator.
  • Seite 25 11/05/10 11:29:49 32Z28610_025 Pull the starter grip lightly until you feel resistance, then pull the starter grip briskly toward in the direction of the arrow as shown below. The starter grip can be drawn back very quickly before you release it. This may pull your hand forcefully toward the engine and cause an injury.

  • Seite 26: Carburetor Modification For High Altitude Operation

    High altitude performance can be improved by specific modifications to the carburetor. If you always operate your generator at altitudes above 1,500 meters (5,000 feet), have your authorized Honda servicing dealer perform this carburetor modification. This engine, when operated at high altitude with the carburetor modifications for high altitude use, will meet each emission standard throughout its useful life.

  • Seite 27: Generator Use

    11/05/10 11:30:02 32Z28610_027 GENERATOR USE The generator produces enough electric power to cause a serious shock or electrocution if misused. Be sure to ground the generator when the connected appliance is grounded. GROUND TERMINAL To ground the terminal of the generator, use a cooper wire with same or larger diameter than the cord of the connected appliance.
  • Seite 28 11/05/10 11:30:12 32Z28610_028 Do not exceed the current limit specified for any one receptacle. Do not modify or use the generator for other purposes than it is intended for. Do not connect an extension to the exhaust pipe. When an extension cable is required, be sure to use a tough rubber sheathed flexible cable (IEC 245 or equivalent).
  • Seite 29 11/05/10 11:30:18 32Z28610_029 AC applications Start the engine and make sure the Output indicator (green) comes Confirm that the appliance to be used is switched off, and plug in the appliance. OUTPUT INDICATOR (GREEN) OVERLOAD INDICATOR (RED) ECO THROTTLE SWITCH If you wish to use the Eco Throttle system, turn the Eco Throttle switch to the ECO position (see page Substantial overloading that continuously lights the Overload...
  • Seite 30 11/05/10 11:30:25 32Z28610_030 AC Circuit Protectors (G/G8, GW, F, IT types) The AC circuit protectors will automatically switch OFF (push button comes out) if there is a short circuit or a significant overload of the generator at receptacle. If an AC circuit protector switches OFF automatically, check that the appliance is working properly and does not exceed the rated load capacity of the circuit before resetting the AC circuit protector ON (pushing the push button in).

  • Seite 31: Overload Indicator

    When an electric motor is started, both the Overload indicator (red) and the Output indicator (green) may come on simultaneously. This is normal if the Overload indicator (red) goes off within 9 seconds. If the Overload indicator (red) stays on, consult your Honda generator dealer.
  • Seite 32 Parallel operation Please read the item ‘‘GENERATOR USE’’ before connecting any equipment to be used. Use only a Honda approved receptacle box for parallel operation (optional equipment except G8 type) when connecting two EU30i generators for parallel operation. RECEPTACLE BOX FOR PARALLEL OPERATION...

  • Seite 33: Front Handle

    11/05/10 11:30:47 32Z28610_033 Never connect the different generator models and types. Never connect a cable other than the receptacle box for parallel operation. Connect and remove the receptacle box for parallel operation with the engine stopped. For single operation, the receptacle box for parallel operation must be removed.
  • Seite 34 11/05/10 11:30:53 32Z28610_034 Be sure to ground the generator when the connected equipment is grounded. GROUND TERMINAL Start the engines and make sure the Output indicators (green) come OUTPUT INDICATOR (GREEN) Confirm that the appliance to be used is switched off, and plug in the appliance.
  • Seite 35 11/05/10 11:31:01 32Z28610_035 DC application The DC receptacle may be used for charging 12 volt automotive-type batteries only. In DC operation, turn the Eco Throttle switch to the OFF position. Connect the charging cable to the DC receptacle of the generator and then to the battery terminals.
  • Seite 36 11/05/10 11:31:11 32Z28610_036 Batteries produce explosive gases: If ignited, and explosion can cause serious injury or blindness. Provide adequate ventilation when charging. CHEMICAL HAZARD: Battery electrolyte contains sulfuric acid. Contact with eyes or skin, even through clothing, may cause severe burns.

  • Seite 37: Oil Alert System

    11/05/10 11:31:16 32Z28610_037 Oil Alert system The Oil Alert system is designed to prevent engine damage caused by an insufficient amount of oil in the crankcase. Before the oil level in the crankcase falls below a safe limit, the Oil Alert system will automatically shut down the engine (the engine switch will remain in the ON position).

  • Seite 38: Stopping The Engine

    11/05/10 11:31:22 32Z28610_038 STOPPING THE ENGINE To stop the engine in an emergency, turn the engine switch to the OFF position. IN NORMAL USE: Switch off the connected equipment and pull the inserted plug. Turn the engine switch to the OFF position. ENGINE SWITCH...
  • Seite 39 11/05/10 11:31:27 32Z28610_039 Turn the fuel tank cap vent lever fully counterclockwise to the OFF position. FUEL TANK CAP VENT LEVER Be sure the fuel tank cap vent lever and the engine switch are in the OFF position when stopping, transporting and/or storing the generator.

  • Seite 40: Maintenance

    Every 2 years (Replace if necessary) (2) Service more frequently when used in dusty areas. These items should be serviced by your Honda servicing dealer, unless you have the proper tools and are mechanically proficient. Refer to the Honda shop manual for service procedures.
  • Seite 41 11/05/10 11:31:45 32Z28610_041 Tools A box wrench, spark plug wrench and wrench handle are supplied with the generator. Use the supplied tools to perform maintenance tasks. Using an incorrect tool may damage the generator. BOX WRENCH SPARK PLUG WRENCH WRENCH HANDLE...

  • Seite 42: Changing Oil

    11/05/10 11:31:51 32Z28610_042 CHANGING OIL Drain the oil while the engine is still warm to assure rapid and complete draining. Make sure to turn the engine switch and the fuel tank cap vent lever to the OFF position before draining. Place wood blocks under the generator to give a clearance of at least 90 mm (3.5 in) as shown.
  • Seite 43 11/05/10 11:32:01 32Z28610_043 Open the oil drain plug cover from the bottom of the generator. Place a suitable container under the oil drain plug. Remove the oil drain plug and sealing washer with the supplied box wrench and wrench handle, and drain the oil into the container thoroughly.

  • Seite 44: Air Cleaner Service

    11/05/10 11:32:08 32Z28610_044 AIR CLEANER SERVICE A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction, service the air cleaner regularly. Service more frequently when operating the generator in extremely dusty areas. Do not use gasoline or low flash point solvents for cleaning. They are flammable and explosive under certain conditions.
  • Seite 45 11/05/10 11:32:14 32Z28610_045 Wash the elements in a solution of household detergent and warm water and rinse thoroughly, or wash in nonflammable or high flash point solvent. Allow the elements to dry thoroughly. If the elements are damaged, replace them. Soak the elements in clean engine oil and squeeze out the excess oil.
  • Seite 46 11/05/10 11:32:22 32Z28610_046 SPARK PLUG SERVICE RECOMMENDED SPARK PLUG: BPR6ES (NGK) W20EPR-U (DENSO) To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. If the engine is hot, allow it to cool before servicing the spark plug. Loosen the cover screw and remove the spark plug maintenance cover.
  • Seite 47 11/05/10 11:32:30 32Z28610_047 Visually inspect the spark plug. Discard it if the insulator is cracked, chipped, or fouled. Clean the spark plug with a wire brush if it is to be reused. Measure the plug gap with a feeler gauge. Correct as necessary by carefully bending the side electrode.

  • Seite 48: Transporting/Storage

    11/05/10 11:32:39 32Z28610_048 TRANSPORTING/STORAGE To prevent fuel spillage when transporting or during temporary storage, the generator should be secured upright in its normal operating position, with the engine switch OFF. The fuel tank cap vent lever is turned fully counterclockwise to the OFF position.
  • Seite 49 11/05/10 11:32:49 32Z28610_049 Secure the generator with ropes or tie-down straps when transporting. Make sure only to use the front and rear handles as attachment points. Do not fasten ropes or straps to any portions of the generator body or the folding handle.
  • Seite 50 11/05/10 11:32:59 32Z28610_050 Storage Before storing the generator for an extended period: Be sure the storage area is free of excessive humidity and dust. Drain the fuel. Gasoline is extremely flammable and is explosive under certain conditions. Perform this task in a well ventilated area with the engine stopped.
  • Seite 51 11/05/10 11:33:04 32Z28610_051 Change the engine oil (see page Remove the spark plug and pour about a tablespoon of clean engine oil into the cylinder. Crank the engine several revolutions to distribute the oil, then reinstall the spark plug. Slowly pull the starter grip until resistance is felt. At this point, the piston is coming up on its compression stroke and both the intake and exhaust valves are closed.

  • Seite 52: Troubleshooting

    (see page Is the spark plug Clean, readjust in good gap and dry the condition? spark plug. Replace it if necessary (see page If the engine still does not start, take the generator to an authorized Honda dealer.
  • Seite 53 ON (see page protector ON? Is the output indicator on? Is the Overload Take the indicator on? generator to an authorized Honda dealer. Check the Take the electrical NO DEFECTS generator to an appliance or authorized equipment for Honda dealer.
  • Seite 54 11/05/10 11:33:25 32Z28610_054 No electricity at the DC receptacle: Is the DC circuit Turn the DC protector ON? circuit protector ON (see page Take the generator to an authorized Honda dealer.

  • Seite 55: Specifications

    11/05/10 11:33:40 32Z28610_055 SPECIFICATIONS Dimensions and Weight Model EU30i Description code EAVJ Length 622 mm (24.5 in) Width 379 mm (14.9 in) Height 489 mm (19.3 in) Dry mass [weight] 35.2 kg (77.6 lbs) Engine Model GX160 Engine type 4-stroke, overhead valve,...
  • Seite 56 11/05/10 16:29:16 32Z28610_056 Noise EU30i Model G/G8, GW, F, IT Type 74 dB (A) Sound pressure level at the workstation (2006/42/EC) Microphone point CONTROL PANEL Center 1.60 m 1.0 m Uncertainty 3 dB (A) Measured sound power level 89 dB (A)

  • Seite 57: Wiring Diagram

    11/05/10 11:33:59 32Z28610_057 WIRING DIAGRAM INDEX (See inside back cover) G/G8, GW, F, IT Types ................W 1 − U Type ....................W 2 − ABBREVIATIONS Symbol Part name Symbol Part name ACCP AC Circuit Protector Rectifier ACNF AC Noise Filter Spark Plug ACOR AC Output Receptacle...

  • Seite 58: Receptacle

    11/05/10 11:34:08 32Z28610_058 RECEPTACLE Type Shape Plug GROUND PIN G/G8, GW GROUND PIN GROUND PIN GROUND PIN...
  • Seite 59 11/05/10 11:34:10 32Z28610_059...
  • Seite 60 11/05/10 11:34:11 32Z28610_060...

  • Seite 61: Wiring Diagram

    11/05/10 11:34:15 32Z28610_061 WIRING DIAGRAM SCHÉMA DE CABLAGE SCHALTPLAN DIAGRAMA DE CONEXIONES...
  • Seite 62 11/05/10 11:34:24 32Z28610_062 −...
  • Seite 63 11/05/10 11:34:32 32Z28610_063 −...
  • Seite 64 11/05/10 11:34:33 32Z28610_064...

  • Seite 65: Major Honda Distributor Addresses

    Weitere Informationen erhalten Sie gerne vom Honda- Kundeninformationszentrum unter der folgenden Adresse oder Telefonnummer: DIRECCIONES DE LOS PRINCIPLES CONCESIONARIOS Honda Para obtener más información, póngase en contacto con el Centro de información para clientes Honda en la dirección o número de teléfono siguientes:...
  • Seite 66 11/05/10 11:34:50 32Z28610_066 AUSTRIA CROATIA FINLAND Honda Motor Europe (North) Hongoldonia d.o.o. OY Brandt AB. Hondastraße 1 Jelkovecka Cesta 5 Tuupakantie 7B 2351 Wiener Neudorf 10360 Sesvete − Zagreb 01740 Vantaa Tel. : ＋ 43 (0)2236 690 0 Tel. : ＋...
  • Seite 67 ＠ ＠ info hondakisgepek.hu honda.produtos honda-eu. ICELAND NETHERLANDS REPUBLIC OF BELARUS Bernhard ehf. Honda Motor Europe (North) Vatnagardar 24-26 Afd. Power Equipment- Scanlink Ltd. 104 Reykdjavik Capronilaan 1 Kozlova Drive, 9 Tel. : ＋ 354 520 1100 1119 NN Schiphol-Rijk...
  • Seite 68 CR honda.ua ventas aucasa.com ＠ taller aucasa.com ＠ SLOVAKIA REPUBLIC SWEDEN UNITED KINGDOM Honda Slovakia, spol. s r.o. Honda Nordic AB Honda (UK) Power Equipment Prievozská 6 821 09 Bratislava Box 50583 - Västkustvägen 17 470 London Road Tel. : ＋...
  • Seite 69 Minato-ku, Tokyo, JAPAN 8. Fait à e) Org 8. Fait Authorized representative Authorized representative Nederla Honda Motor Europe Ltd. Aalst Office EG-verk Neder Honda Motor Europe Ltd. Aalst Office Wijngaardveld 1 (Noord V), 1. Onder EG-ve Wijngaardveld 1 (Noord V), de gema 1.
  • Seite 70 Français. (French) Italiano (Italian) Deutsch (German) Déclaration CE de Conformité Français. (French) Dichiarazione CE di Conformità Italiano (Italian) EG-Konformitätserklärung Deutsch (German) 1. Le sous signé, Piet Renneboog, de la part du Déclaration CE de Conformité 1. Il sottoscritto, Piet Renneboog, in qualità di Dichiarazione CE di Conformità...
  • Seite 71 Português ( Portuguese ) Português ( Portuguese ) Polski ( Polish ) Polski ( Polish ) Suomi / Suomen kieli (Finnish) Suomi / Suomen kieli (Finnish) Lietuvių ka Lietuv Declaração CE de Conformidade Declaração CE de Conformidade Deklaracja zgodności WE Deklaracja zgodności WE EB atitikties EY-VAATIMUSTENMUKAISUUSVAKUUTUS...
  • Seite 72 Lietuvių kalba (Lithuanian) Lietuvių kalba (Lithuanian) Български (Bulgarian) Български (Bulgarian) Norsk (Norwegian) Norsk (Norwegian) EB atitikties deklaracija ЕО декларация за съответствие EF- Samsvarserklæring EB atitikties deklaracija ЕО декларация за съответствие EF- Samsvarserklæring 1. Įgaliotojo atstovo vardu pasirašęs Piet 1.Undertegnede Piet Renneboog på vegne av ettu 1.

Inhaltsverzeichnis