Specifications; General Safety Rules - Makita 5704R Betriebsanleitung

ENGLISH
1 A typical illustration of proper
hand support, workpiece sup-
port, and supply cord routing
(if applicable).
2 To avoid kickback, do support
board or panel near the cut.
3 Don't support board or panel
away from the cut.
4 Hex wrench
5 Shaft lock
6 Tighten

SPECIFICATIONS

Model
Blade diameter ............................................. 190 mm
Max. cutting depth
At 90° ..........................................................66 mm
At 45° ..........................................................46 mm
-1
No load speed (min ) ...................................... 4,900
Overall length ............................................... 345 mm
Net weight ....................................................... 4.6 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and miter cuts with angles to
45° in wood while in firm contact with the workpiece.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
SAVE THESE INSTRUCTIONS.
Work area safety
1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
6
Explanation of general view
7 Loosen
8 Saw blade
9 Outer flange
10 Inner flange
11 Hex socket head bolt
12 Setting protuberances
13 Hex socket head bolt
(For adjusting riving knife)
14 Cutting depth
15 Lever
16 Thumb screw
Electrical safety
4.
5704R
5.
6.
7.
8.
Personal safety
9.
10. Use safety equipment. Always wear eye protection.
GEA001-3
11. Avoid accidental starting. Ensure the switch is in
12. Remove any adjusting key or wrench before
13. Do not overreach. Keep proper footing and bal-
14. Dress properly. Do not wear loose clothing or
17 For 45° ° ° ° bevel cuts
18 For straight cuts
19 Base plate
20 Lock-off button
21 Switch trigger
22 Vacuum cleaner
23 Limit mark
24 Brush holder cap
25 Screwdriver
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appro-
priate conditions will reduce personal injuries.
the off-position before plugging in. Carrying
power tools with your finger on the switch or plug-
ging in power tools that have the switch on invites
accidents.
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
ance at all times. This enables better control of the
power tool in unexpected situations.
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.