Inhibition Of The Out Signal; Direct Modification Of The Set Point; Displaying The Set Point Set; Lamp Test - Eliwell EWTQ925 Bedienungsanleitung

5 . 6

5 . 6 INHIBITION OF THE OUT SIGNAL

5 . 6 INHIBITION OF THE OUT SIGNAL INHIBITION OF THE OUT SIGNAL INHIBITION OF THE OUT SIGNAL
5 . 6 5 . 6 INHIBITION OF THE OUT SIGNAL
These products allow to turn the out signal OFF
manually to stop the control.
To turn the out signal OFF, press the
first and then press the FUNC pushbutton.
Keeping them both pressed for more than 3
seconds, the instrument will show "
the set point value.
The instrument will display "
indicating the set point; the out signal will switch
OFF and the instrument will work as a simple
indicator.
When the control outs are disabled, the alarms are
also disabled and forced to the no-alarm condition.
The modification of the control parameters is still
enabled.
To return to normal control, press the
first and then press the FUNC pushbutton.
Keeping them both pressed for more than
3 seconds, the instrument returns to normal
display mode.
NOTES NOTES NOTES :
NOTES NOTES
1) If the out is turned OFF when the SMART
function is performing the first part of the SMT
algorithm (LED SMT flashing), the SMART
function will be aborted and when the
instrument comes back to the normal control,
the SMART function will be disabled.
If the out is turned OFF when the SMART
function was performing the second part of the
SMT algorithm (LED SMT lit), the SMART
function will be stopped and, when the
instrument comes back to the normal control,
the smart function will also be activated.
2) If the instrument is turned OFF with the out
power off function enabled, at the next start up
this function will automatically be enabled
again.
pushbutton
" instead of
OFF OFF
OFF OFF OFF
" instead of
OFF OFF OFF OFF OFF
pushbutton
G B G B G B G B G B
5 . 7 DIRECT MODIFICATION OF 5 . 7 5 . 7 DIRECT MODIFICATION OF DIRECT MODIFICATION OF DIRECT MODIFICATION OF
5 . 7 5 . 7 DIRECT MODIFICATION OF
THE SET POINT THE SET POINT THE SET POINT THE SET POINT THE SET POINT
The instrument modifies the set point value without
using the FUNC pushbutton.
When direct access to set point modification is
required, proceed as follow:
1) Press pushbutton
2 seconds; the set point value will be
displayed and it will start to change.
2) Using the and
desired value.
3) When the desired value is reached, DO NOT
press any pushbutton, the new set point will
become operative after 2 seconds after the
pushbuttons were last pressed and the
instrument will return to the "normal display".
If during this procedure the modification is not to
be saved, press the FUNC pushbutton
immediately (within 2 seconds); the instrument
automatically returns to the normal display without
saving the new set point.
5.8 5.8 5.8 5.8

5.8 DISPLAYING THE SET POINT SET

DISPLAYING THE SET POINT SET DISPLAYING THE SET POINT SET DISPLAYING THE SET POINT SET DISPLAYING THE SET POINT SET
(single display model) (single display model) (single display model) (single display model) (single display model)
To display the set point set, press the
pushbutton. The SP led lights up.
The set point value will appear on the display.
To return to the display of the value measured
press pushbutton
5 . 9 5 . 9 5 . 9

5 . 9 LAMP TEST

5 . 9 LAMP TEST LAMP TEST LAMP TEST LAMP TEST
To check the display efficiency, press pushbuttons
+ FUNC. The instrument will turn ON, with a
50% duty cycle, all the LEDs of the display (this
state is called LAMP TEST).
No time out is applied to the LAMP TEST.
To return to the normal display mode, press
pushbuttons + FUNC again.
13
or for more than
pushbuttons, set the
again.