Herunterladen Inhalt Inhalt Diese Seite drucken

Accessories - Carlisle TEKNA BASECOAT Technisches Bulletin

Grundlackauftrag-fließbecher-spritzpistole für profis
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Troubleshooting Possible Problems in Operation
CONDITION
Fluid leaking or dripping
from front of gun
Fluid dripping or leaking
from bottom of cup
Runs and sags
Thin, sandy coarse finish
drying before it flows out
Thick, dimpled finish
"orange peel"

Accessories

HAV-555
702576
DeVilbiss
TEKNA 900cc
Air Adjusting Valve
Aluminum Cup
with Gauge
Easy to use and clean
Use to precisely set
air pressure to gun.
design.
703901
HV20 Air Cap Test Kit
The purpose of this test
kit is to measure air cap
atomizing air pressure at
the center air port of the air
cap. Used to confirm code
compliance and as a daily
quality control measure.
Automotive Refinish Quick Connects
For HVLP Guns (Air)
High Flow Type.
HC-4419 Stem
HC-4719 Coupler
1/4" NPT(F)
1/4" NPT(M) /NPS(M)
HC-1166 Stem
HC-4720 Coupler
1/4" NPT(M)
1/4" NPT(F)
TB-1018-R1 (2/2018)
CAUSE
Fluid nozzle or fluid needle worn
or damaged.
Foreign matter in fluid nozzle.
Fluid needle spring broken.
Wrong size fluid needle or
fluid nozzle.
Cup loose on gun.
Cup threads dirty.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun motion
too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
HAV-512
192212 Professional
Adjusting Valve
Spray Gun
Cleaning Kit
Contains six preci-
sion tools designed
Use to control air
to effectively clean
usage at gun.
all DeVilbiss, Binks,
Finishline and other
brand spray guns.
40-128
Twin Cartridge,
Paint Spray
Respirator
NIOSH-Certified
(TC84A-1623) for respira-
Gun holder for up
tory protection in atmos-
to three gravity feed
pheres not immediately
spray guns.
dangerous to life.
HAF-507 Whirlwind™
In-Line Air Filter
Removes water, oil,
and debris from the
air line.
15 / 16
(cont'd)
CORRECTION
Replace fluid nozzle and fluid needle.
Clean.
Replace.
Replace fluid nozzle and fluid needle.
Tighten
Clean.
Turn fluid adjusting knob clockwise
or switch to smaller fluid nozzle and
fluid needle size.
Mix properly or apply light coats.
Hold gun at right angle to work and adapt
to proper gun technique.
Check distance. Normally approx.
150–200 mm (6–8").
Reduce air pressure and check
spray pattern.
Follow paint manufacturer's mixing
instructions.
Check distance. Normally approx.
150–200 mm (6–8"). Too much material
coarsely atomised.
Increase air pressure or reduce
fluid flow.
Follow paint manufacturer's mixing
instructions.
Follow paint manufacturer's mixing
instructions.
Properly clean and prepare.
JGA-156-K10
Spring Clips
Joins any single
p i e c e D e V i l b i s s
air cap with latest
version retaining
ring. Helps prevent
p a r t
l o s s
a n d
p r o v i d e s e a s i e r
assembly.
803616
192219
Multi Spray Gun
Gun Holder
Holder
Gun holder made
to hold guns with
gravity cups.
702740 TEKNA Wrench
14 mm
For maintenance use.
EN
192218 Scrubs
®
Hand Cleaner Towels
S c r u b s
a r e a p r e -
®
moistened hand cleaner
towel for painters, body
men and mechanics that
go where you go and no
water is needed.
Spray Gun Lube
SSL-10 (2 oz. bottle)
Compatible with
all paint materi-
als; contains no
silicone or petro-
leum distillates to
contaminate paint.
SDS Sheet avail-
able upon request.
10 mm
www.carlisleft.com

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

702736

Inhaltsverzeichnis