Important Remarks; Important Safety Instructions - Cardin Elettronica EL series Installationsanleitung

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICU-
LAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL
INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM AND CREATE DANGER
SITUATIONS FOR THE USERS OF THE SYSTEM.
•
These instructions are aimed at professionally qualified "INSTALLERS
OF ELECTRICAL EQUIPMENT" and must respect the local standards
and regulations in force. All materials used must be approved and
must suit the environment in which the installation is situated.
• All maintenance operations must be carried out by professionally
qualified technicians. Before carrying out any cleaning or maintenance
operations make sure the power is disconnected at the mains.
• This appliance must be used exclusively for the purpose for which it
has been made. "i.e. for traffic control".
The appliance may be used to control passageways with widths of
3 m, 4 m and 6 m.
• The unit may be fitted both to the right and to the left of the pas-
sageway.
• The automation is fitted with an anti-tamper system protecting its
internal mechanisms. If the system is forced it will release the boom
and boom holder from the mechanism thus protecting it from damage.
Normal operation can be obtained by replacing the broken safety
pin.
• This product and all its relative components has been designed and
manufactured by Cardin Elettronica who have verified that the product
conforms in every aspect to the safety standards in force.
Any non authorised modifications are to be considered improper
and therefore dangerous. The manufacturer accepts no liability for
situations arising from the use of an electrical installation which does
not conform to the local standards and regulations in force and in
particular when the earthing circuit is not efficient.

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the following
public safety conditions are satisfied:
1) Ensure that the boom operating installation is far enough away from
the main road to eliminate possible traffic disruptions.
2) The operator must be installed on the inside of the property and not
on the public side of the gate. The gates must not swing outwards
onto a public area.
3) The gate operator is designed for use on gates through which vehicles
are passing. Pedestrians should use a separate entrance.
4) The gate must be in full view when it is operating therefore controls
must be situated in a position where the operator can see the gate
at all times.
5) At least two warning signs (similar to the example on the right) should
be placed, where they can be easily seen by the public, in the area
of the system of automatic operation. One inside the property and
one on the public side of the installation.
These signs must be indelible and not hidden by any objects (such
as tree branches, decorative fencing etc.).
6) Make sure that the end-user is aware that children
and/or pets must not be allowed to play within the
area of a gate installation. If possible include this
in the warning signs.
7) A correct earth connection is fundamental in order
to guarantee the electrical safety of the machine
8) If you have any questions about the safety of the
gate operating system, do not install the operator.
Contact your dealer for assistance.
IMPORTANT REMARKS
TECHNICAL DESCRIPTION
710/EL313C - 710/EL413C - 710/EL613
Automation for 3 m, 4 m and 6 m booms with a 230 Vac motor com-
plete with on board electronics and the following functions: automatic,
semiautomatic, manual. The programmer can be fitted with a standard
Cardin radio receiver card and with all the devices required to carry
out an automatic installation.
• 230V 50 Hz motor with tempered steel never ending screws, incor-
porated overload protection and a cooling fan;
- lockable flip-back upper hood (giving access to the commands
and the electronic programmer) in shock-proof plastic fitted with
emergency stop microswitches;
- manual release handle in nylon reinforced with glass fibre;
- irreversible second stage reduction unit with tempered steel gears
and first stage reduction worm gear in highly reliable self-lubricating
POM, mounted on a cast aluminium stator;
- zinc-plated steel geared motor support base;
- boom support levers and joints in zinc-plated steel;
- balancing springs in highly reliable steel;
- lubrication using permanently fluid grease;
- barrier bodywork in spray painted aluminium;
- lockable access door fitted with emergency stop microswitches
giving access to the manual release components;
- incorporated warning lights;
- closing direction travel limit allowing the position of the boom
to be adjusted horizontally;
- adjustable opening direction travel limit with setting screw;
- self-rupturing security screw supplied with the appliance.
Accessories
716/EL320 - 716/EL420
3 m and 4 m anodised aluminium booms complete with a rubber
profile.
716/EL601
6 m anodised aluminium boom complete with a rubber profile.
716/EL324ASK1
3 m articulated boom complete with a rubber profile. A special
device inside the boom allows it to fold backwards when the barrier
is opening.
716/ELSM
Mobile boom support pole (950 mm high).
716/ELFS1
Fixed boom support pole (950 mm high).
716/ELSA
Retractile anodised aluminium mesh (length 2000 mm x height 600
mm). Three pieces are required for a 6 m boom.
716/ELLAMP
WARNING
Warning light kit for transforming a normal hood into a hood with
AUTOMATIC OPENING
KEEP CLEAR
warning lights (only supplied as a spare part).
716/ELSR
Reflective tape in strips of 250 mm x 50 mm.
950/XLPBS1
Pressure switch for safety buffers. When connected to a closed rubber
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
buffer it translates a pneumatic signal into an electrical command
NEAR THE INSTALLATION
which can be interpreted by the electronic programmer as an inversion
command. Complete with a 1 m long 6 x 1 diameter flexible tube and
a connection joint to interface with the closed rubber tube.
16
IMPORTANT REMARKS
. NOT READING THESE IMPORTANT