Important Remarks; User Instructions; Installation Instructions; Important Safety Instructions - Cardin Elettronica EL series Betriebsanleitungen

IMPORTANT REMARKS

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH READ THE FOLLOWING REMARKS CARE-
FULLY BEFORE PROCEEDING WITH THE INSTALLATION. PAY PARTICULAR ATTENTION TO ALL
THE PARAGRAPHS MARKED WITH THE SYMBOL
TIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM.
• These instructions are aimed at professionally qualified
"INSTALLERS OF ELECTRICAL EQUIPMENT" and must
respect the local standards and regulations in force.
All materials used must be approved and must suit the
environment in which the installation is situated.
• This appliance must be used exclusively for the purpose
for which it has been made. "i.e. for traffic control" Any
non authorised modifications are to be considered improper
and therefore dangerous.
The manufacturer accepts no liability for situations arising
from the use of an electrical installation which does not
conform to the local standards and regulations in force and
in particular when the earthing circuit is not efficient.
USE
The appliance may be used to control passageways with a
maximum width of 3 m. The appliances may be fitted both to
the right and to the left of the passageway.
This manual covers the following models:
710/EL3024 Electromechanical barrier with a 24Vdc motor,
incorporated electronics, buffer battery, auto-
matic and semiautomatic functions, torque
limiter and S449 radio frequency decoder.
716/EL3024A Ø 60 mm - 3000 mm long bar complete with
bar holder arm with which to connect it to the
barrier
TECHNICAL DESCRIPTION
- 24Vdc motor with a steel never ending screw.
- Carter in shock-proof plastic.
- Manual release components in reinforced plastic.
- Geared motor with steel gears enclosed in a die cast two-
piece aluminium shell.
- Motor support base in zinc-plated steel
- Boom holder in arm in die cast aluminium.
- Lubrication using permanently fluid grease.
- Barrier cabinet in spray painted die cast aluminium
- Incorporated warning light

IMPORTANT SAFETY INSTRUCTIONS

It is the responsibility of the installer to make sure that the
following public safety conditions are satisfied:
1) Ensure that the installation is far enough away from the
main road to eliminate possible traffic disruptions.
2) The boom when moving vertically must not interfere with
overhead cables or other such obstacles.
3) The barrier is designed for passageways through which
vehicles are passing. Pedestrians should use a separate
entrance.
4) The barrier must be in full view when it is operating therefore
controls must be situated in a position where the operator
can see the barrier at all times.
5) At least two warning signs (similar to the example on the
right) should be placed, where they can be easily seen by
the public, in the area of the system of automatic opera-
tion. One inside the property and one on the
public side of the installation. These signs
must be indelible and not hidden by any
objects (such as tree branches, etc.).
6) Make sure that the end-user is aware that
children and/or pets must not be allowed to
play within the area of a barrier installation. If
possible include this in the warning signs.
IMPORTANT REMARKS
. NOT READING THESE IMPORTANT INSTRUC-
7) If you have any questions about the safety of the barrier,
do not install it. Contact your dealer for assistance.

USER INSTRUCTIONS

WARNINGS FOR THE USER
Before carrying out any cleaning or maintenance operations
make sure the power is disconnected at the mains.
The minimum controls which may be installed are OPEN-
STOP-CLOSE, these controls must be installed in a location
not accessible to children.
During the opening/closing manoeuvre check for correct
operation and activate the emergency stop button in case
of danger.
During blackouts the gate can be released and manually
manoeuvred (see manual release pag.12).
Attention! The boom is not balanced and must be
held during manual release
In case of failure or operational anomalies switch off the power
at the mains do not attempt to repair the appliance yourself.
Periodically check the correct operation of all safety devices
(photoelectric cells etc.)
Eventual repair work must be carried out by specialised per-
sonnel using original spare parts.
The appliance is suitable for continuous operation (see techni-
cal data on page 20).

INSTALLATION INSTRUCTIONS

• The ground must be stable enough to firmly hold the plinth
and the anchor plates.
• Where possible protect the barrier cabinet from accidental
knocks by passing vehicles.
• Work out the run of the cables according to the command
and control devices fitted and make sure the system con-
forms to the local standard and regulations in force (see
installation example fig.1 pag. 2).
FITTING THE UNIT
Once you have decided on the exact installation position
proceed as follows:
- prepare a cement base with the base plate and anchors
"A" embedded. The cable passage tube "B" and the four
threaded bolts "D" M8 must protrude (30mm) from the base
plate.
- the base plate must be perfectly in square, its surface must
be clean and the four threaded bolts must emerge perpen-
dicularly.
Note: the cement base should preferably protrude 50 mm
out of the ground in order to avoid water build up which
could damage the appliance.
• To install the barrier proceeds as follows:
- remove the 4 self locking nuts "D" from the four threaded
bolts (used to fasten down the anchors) and insert the base
WARNING
of the barrier "C". Fasten down the barrier using the 4 self
locking nuts and washers "D" supplied with the appli-
AUTOMATIC OPENING
KEEP CLEAR
ance.
- it is also possible to fasten the barrier to an already existing
cement base as long as the thickness of the base is great
enough to guarantee a strong hold for the rawlplugs.
We advise you to use the following type of rawlplug: "Steel
anchor bolts M8/diam. 14 for heavy duty use".
CHILDREN OR PETS MUST NOT
BE ALLOWED TO PLAY ON OR
NEAR THE INSTALLATION
11
IMPORTANT REMARKS