Atomik 18003 Bedienungsanleitung Seite 5

ESC SETUP CONT.
ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT. ESC SETUP CONT.
1
Turn on transmitter.
Hold full throttle and connect battery.
- Continue to hold full throttle until musical tone sounds (5 seconds).
* CONTINUE TO HOLD FULL THROTTLE WHILE MOVING ON TO STEP 2*
FULL THROTTLE
2
The ESC will emit a series of beep patterns. Each pattern represents a category:
To select tuning category, move throttle to neutral after desired beep pattern sounds.
*YOU ARE NOW IN THE SELECTED TUNING CATEGORY*
FULL to NEUTRAL
3
Your ESC will again emit a series of beep tones. The beep tones represent a
di erent value. (Review chart below for tone diagram).
To select a value, simply wait for the desired beep tones to emit and pull full throttle.
Move the throttle to the neutral position. Within 2 seconds you will exit program mode. If you
FULL THROTTLE
continue to full throttle position, you will go back to step #2 and you can select a different tuning
category.
Tuning
"B"
Category
1 Short Beep
Running Forward
Mode Only
LiPO Auto
Cell # Calculate
Low
No
Voltage
Protection
Cut-off
Timing 0º
CAUTION: LOW VOLTAGE CUT-OFF
Do not use "NO PROTECTION" when using LiPO battery packs. Monitor the battery pack temperatures after
each run. Do not allow the battery pack temperatures to exceed 120º F/ 52º C while in use. Select a higher low
voltage cut-off setting to help reduce the temperature of the battery packs. It is OK to use "NO PROTECTION"
when using NiCD or NiMH battery packs.
1 8 00 3
Entering Program Mode
Selecting Category
1. "Beep"
2. "Beep-Beep"
3. "Beep-Beep-Beep"
4. "Beep-Beep-Beep-Beep"
Selecting Value for Category
If you are unsure if you have exited the program mode, you can disconnect
the battery and your programming will be saved.
"BB" "BBB"
2 Short Beeps 3 Short Beeps
Forward &
Backward
2 3
Cells Cells
2.8V/Cell 3.0V/Cell
3.75º 7.5º
Running Mode
LiPO Cells
Low Voltage Cutoff Threshold
Timing
BEEP TONES
"BBBB" "Beep-"
4 Short Beeps 1 Long Beep
4 5
Cells Cells
3.2V/Cell 3.4V/Cell
11.25º 15º
Shaded Fields are Factory Settings (Recommended).
5
"Beep-B" "Beep-BB"
1 Long 1 Long
1 Short Beep 2 Short Beeps
6
Cells
18.75º 22.5º
ATOMIK-RC.COM
"Beep-BBB"
1 Long
3 Short Beeps
26.25º