Product Description And Specifications - Bosch PWS 1000-125 Originalbetriebsanleitung

OBJ_BUCH-1961-006.book Page 19 Wednesday, June 24, 2015 9:26 AM
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Release the On/Off switch and set it to the off position
when the power supply is interrupted, e. g., in case of a
power failure or when the mains plug is pulled.
 Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for cutting, roughing and brushing of
metal and stone materials without the use of water.
Technical Data
Angle Grinder
Article number
Rated power input
Rated speed
Speed control adjustment
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Reduced starting current
Constant electronic control
Speed preselection
Soft starting
Kickback stop
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Bosch Power Tools
For cutting with bonded abrasives, a special cutting guard
(accessory) must be used.
When cutting in stone, provide for sufficient dust extraction.
With approved sanding tools, the machine can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Release lever for protection guard
2 Spindle lock button
3 On/Off switch
4 Thumbwheel for speed preselection
(PWS 1000-125 CE/PWS 1300-125 CE)
5 Auxiliary handle (insulated gripping surface)
6 Grinder spindle
7 Protection guard for grinding
8 Mounting flange
9 Grinding wheel*
10 Clamping nut
11 Quick-clamping nut
12 Protection guard for cutting*
13 Cutting disc*
14 Hand guard*
15 Rubber sanding plate*
16 Sanding sheet*
17 Round nut*
18 Cup brush*
19 Cutting guide with dust extraction protection guard *
20 Diamond cutting disc*
21 Handle (insulated gripping surface)
22 Direction-of-rotation arrow on housing
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
PWS ... 1000-125
3 603 ... CA2 6..
W 1001
-1
min 11000
-1
min –
mm 125
M 14
mm 22
–
–
–
–
–
English | 19
*
1000-125 CE 1300-125 CE
CA2 8.. CA2 9..
1010 1300
11500 11500
2800 – 11500 2800 – 11500
125 125
M 14 M 14
22





1 609 92A 1C8 | (24.6.15)
22




