Snom M325 Bundle Schnellstartanleitung Seite 11

en
Health and safety information FCC
Exposure to Radio Frequency (RF) Signals
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
The guidelines are based on the safety standards previously set by both U.S. and international standards bodies:
This product has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled
environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and has been tested in
accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE Std. 1528-
2003 (December 2003).
RF exposure FCC
Tests for SAR are conducted using standard operating positions specified by the FCC with the phone transmitting at its
highest certified power level in all tested frequency bands. The actual SAR level of the phone in operation can be well
below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only
the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the
power output.
Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed
the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and
locations (e.g., at the ear and worn on the body) as required by the FCC for each model. Body-worn measurements may
differ among phone models, depending upon available accessories and FCC requirements. The highest SAR value for this
phone when tested for use at the ear is 0.42 W/kg. While there may be differences between the SAR levels of various
phones and at various positions, they all meet the government requirement for safe exposure.
For body worn operation, to maintain compliance with FCC RF exposure guidelines, use only accessories that contain no
metallic components and provide a separation distance of 15mm (0.6 inches) to the body. Use of other accessories may
violate FCC RF exposure guidelines and should be avoided.
Regulatory information Canada
IC number M300 base station: 4979B-X9430
IC number M25 handset: 4979B-CT4088
Interference information
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Privacy of communications may not be ensured when using this equipment. La confidentialité des communications ne
peut pas être garantie avec cet équipement.
Exposure to Radio Frequency (RF) Signals
This product is a radio transmitter and receiver. It is designed and manufactured not to exceed this emission limit for
exposure to radio frequency (RF) energy set by the Ministry of Health (Canada), Safety Code 6. These limits are part of
comprehensive guidelines and established permitted levels of RF energy for the general population. These guidelines
are based on the safety standards previously set by international standard bodies. These standards include a substantial
safety margin designed to assure the safety of all persons, regardless of age and health.
This device and its antenna must not be colocated or operating in conjunction with any other antenna or transmitter.
This device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled
environmental / general public exposure limits specific in ANSI/IEEE C95.1-1992 and had been tested in accordance with
the measurement procedures specified in IEEE 1528-2003.
This product meets the applicable Industry Canada technical specifications. / Le présent matériel est conforme aux
specifications techniques applicables d'Industrie Canada.
11
qsg_M325.indd 11 29.10.2014 09:54:38