Maintenance - Bestway Lay-Z-Spa Bedienungsanleitung

Alarms
Causes
The water flow sensors
work without pressing the
filter or heat button.
After starting or during the
functions of filtering or/and
heating, the water flow
sensors do not detect
water flow.
The pump's thermometer
reads the water
temperature below
4°C (40°F).
The pump's thermometer
reads the water
temperature over
50°C (122°F).
The pump's thermometer
connections have issues.
The manual reset thermal
cut-out has problem.
Ground Connection Failed.

MAINTENANCE

NOTE: Your spa will require additional air to be added from time to time. Changes in temperature from day to night will
change the pressure in the spa and may cause a certain amount of deflation. Please follow the Assembly instructions
and drain the spa before inflating to the accurate pressure needed.
CAUTION: YOU MUST ENSURE THE PUMP IS UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE TO AVOID RISK OF
INJURY OR DEATH.
Filter Cartridge Maintenance
NOTE: To ensure your spa water stays clean,
check and clean your filter cartridges
every day follow the steps below.
NOTE: We recommend changing your filter cartridges every week or, if the filter cartridges remain soiled and discolored, they
should be replaced.
Water Maintenance
Keeping your SPA water clean and chemically balanced is necessary. Simply cleaning the filter cartridge is not enough for
proper maintenance, we recommend you use pool chemicals to maintain water chemistry and chlorine or bromine tablets (do not
use granules) with the chemical floater.
Water quality will be directly related to frequency of use, number of users and overall maintenance of the spa. The water should
be changed every 3 days if there is no chemical treatment being performed with the water.
Note: We recommend you take a shower before using your Lay-Z-Spa, as cosmetic products, lotions, and other residues on the
skin can quickly degrade water quality.To use the chemical floater, please follow the below instruction.
Using chemical tablets (not included):
Using chemical liquid (not included):
S-S-005855/14x21cm/54112; 54113; 54123; 54129; 54148; 54154; 54171; 54174; 54175; 54183; 54186/欧规AirJet SPA说明书/JS-YF-2016-B-16420/
Reasons
1. The water flow sensor flags didn't fall back
into the correct position.
2. The water flow sensors are broken.
1. You forgot to remove the 2 stopper caps from
inside the pool.
2. Filter cartridges are dirty.
3. Activate the filter or heat system and put your
hand in front of the outlet pipe inside the pool to
check if you can feel water flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm appears,
the water flow sensors are broken.
1. The water temperature is lower than
4°C (40°F)
2. If the water temperature is higher than
7°C (44.6°F), the pump's thermometer is broken.
1. The water temperature is over 50°C (122°F)
2. If the water temperature is lower than
45°C (113°F), the pump's thermometer is
broken.
1. The pump's thermometer connectors don't
work properly.
2. The pump's thermometer is broken.
The manual reset thermal cut-out trips off.
1. The ground bonding of your home has some
problem.
2. The pump has some problem.
P6653
Filter Set
11
Solutions
1. Unplug the plug gently, strike the side of the pump but not violently, and
plug it back in.
2. Contact your local Bestway After Sales service point to get instructions.
1. Remove the 2 stopper caps before heating, refer to Assembly section in the
User's Manual.
2. Remove the filter set from inside the pool and push the filter or heat button. If
no alarm appears, clean or change the filter cartridges install the filter set
inside the pool.
3. Contact your local Bestway After Sales service point to get instructions.
1. The spa is not designed to operate with water temperatures lower than
4ºC (40°F). Unplug the pump and only re-start the pump when the water
temperature reaches 6°C (43°F).
2. Contact your local Bestway After Sales service point to get instructions.
1. The spa is not designed to operate with water temperatures greater than
40°C (104°F). Unplug the pump and only re-start the pump when the water temperature
reaches 38°C (100°F) or lower.
IMPORTANT: Before you re-start the pump, push the pump's reset button.
2. Contact your local Bestway After Sales service point to get instructions.
Contact your local Bestway After Sales service point to get instructions.
1. Unplug the pump and push the reset button, then plug the pump back in.
2. In case the alarm still remains, check the RESET BUTTON section in
manual.
3. Contact your local Bestway After Sales service point to get instructions.
Contact your local Bestway Aftersales Service Center for instructions.
58323
Filter Cartridge
S-S-005855