Stiga SNOW MASTER Bedienungsanleitung Seite 13

HOW TO ASSEMBLE THE CHUTE DEFLECTOR
1. (Figure 7) Remove carriage bolt (1).
2. Raise the chute deflector (2) into operating position (3).
3. Fasten chute deflector (2) to flange (4) with carriage
bolts (1). Make sure to install with head of the carriage
bolts (1) on the inside of the flange (2).
4. Fasten with washers (5) and locknuts (6).
5. Tighten locknuts (6) securely.
NOTE: Make sure all carriage bolts in flange are tight.
DO NOT OVERTIGHTEN.
HOW TO REPLACE THE BELTS
The drive belts are of special construction and must be re-
placed with original factory replacement belts available from
your nearest authorized service center.
Some steps require the assistance of a second person.
How To Remove the Auger Drive Belt
If the auger drive belt is damaged, the snow thrower will not
discharge snow. Replace the damaged belt as follows.
1. Disconnect the spark plug wire.
2. (Figure 21) Loosen the bolts (3) on each side of the bot-
tom panel (2).
3. Remove the bottom panel (2).
4. (Figure 18) Remove screw (2) from belt cover (1). Re-
move the belt cover (1).
5. (Figure 19) Loosen the belt guide (9). Pull the belt guide
(9) away from the auger drive pulley (10).
6. Pull the idler pulley (3) away from the auger drive belt
(4).
7. Remove the old auger drive belt (4) from the auger
drive pulley (10) and from the engine pulley (11). Re-
place the auger drive belt (4) with an original factory re-
placement belt available from an authorized service
center.
8. Install the new auger drive belt (4) onto the auger drive
pulley (10) and onto pulley (11).
9. Adjust the auger drive belt (4). See "How To Adjust The
Auger Drive Belt" in the Maintenance section.
10. Adjust the belt guide (9). See "How To Adjust The Belt
Guide" in the Maintenance section.
11. (Figure 18) Install the belt cover (1). Tighten screw (2).
12. Check the adjustment of the cables. See "How To Check
And Adjust The Cables" in the Maintenance section.
13. Connect the spark plug wire.
HOW TO REMOVE THE TRACTION DRIVE BELT
If the snow thrower will not move forward, check the traction
drive belt for wear or damage. If the traction drive belt is
worn or damaged, replace the belt as follows.
ENGLISH
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See "How To Remove The
Auger Drive Belt" in the Maintenance section.
3. (Figure 19) Remove the e–ring (17) from one end of the
swing plate axle rod (18). Remove the swing plate axle
rod (18) to allow the the swing plate to pivot forward.
4. Remove the traction drive spring (16).
5. Remove the old traction drive belt (13) from the trac-
tion drive pulley (14) and from the engine pulley (15).
Replace the traction drive belt (13) with an original fac-
tory replacement belt available from an authorized serv-
ice center.
6. Install the new traction drive belt (13) onto the traction
drive pulley (14) and onto engine pulley (15).
7. Make sure the traction drive idler pulley (12) is proper-
ly aligned with the traction drive belt (13).
8. Attach the traction drive spring (16).
9. Install the swing plate axle rod (18) and secure with the
e–ring (17) removed earlier.
10. (Figure 30) The bottom of the swing plate (20) must be
positioned between the alignment tabs (19). Make sure
the swing plate (20) is properly secured.
NOTE: If the drive will not engage after the traction
drive belt has been replaced, then check to make sure that
the swing plate is positioned between the alignment tabs
(19).
11. (Figure 19) Install and adjust the auger drive belt (4).
See "How To Remove The Auger Drive Belt" in the
Maintenance section.
12. Adjust the belt guide (9). See "How To Adjust The Belt
Guide" in the Maintenance section.
13. (Figure 21) Install the bottom panel (2).
14. Tighten the bolts (3) on each side of the bottom panel
(2).
15. (Figure 18) Install the belt cover (1). Tighten screw (2).
16. Check the adjustment of the cables. See "How To Check
And Adjust The Cables" in the Maintenance section.
17. Connect the spark plug wire.
How To Adjust The Belt Guide
1. Disconnect spark plug wire.
2. (Figure 18) Remove screw (2). Remove the belt cover
(1).
3. (Figure 2) Engage the auger drive lever (5).
4. (Figure 22) Measure the distance between the belt guide
(2) and auger drive belt (3). The correct distance (4) is
1/8 inch (3.175 mm).
5. If an adjustment is necessary, loosen the mounting bolt
for the belt guide (2). Move the belt guide (2) to the cor-
rect position
GB
13