Stiga PARK 4WD PRO Svan Gebrauchsanweisung Seite 54

EN
2.4.9 Power take-off (2:K)
Switch for engaging/disengaging the electromag-
netic power take-off for operating front-mounted
accessories. Two positions:
1. Press the front part of the switch – the
power take-off is engaged. The symbol
will light up.
2. Press the rear part of the switch – the
power take-off is disengaged.
2.4.10 Hour meter (3:P)
Indicates the number of working hours. Only
works when the engine is running.
2.4.11 Cruise control (2:N)
A switch for activating the cruise control. The
cruise control locks the pedal (1:F) in the desired
position.
1. Press down the pedal (1:F) until the de-
sired speed is obtained. Then press the
front part of the switch to activate the
cruise control. The symbol will light up.
2. Disengage the cruise control by releas-
ing it with the pedal (1:B) or pressing the
rear part of the switch.
2.4.12 Cutting height adjustment (2:J)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (3:Q).
2.4.13 Sand spreader (2:O)
The machine has been designed for electrical ad-
justment of a sand spreader (accessory).
The switch is used to start and stop the
12V
spreader.
Cables for connecting the sand spreader are at the
rear of the machine.
2.4.14 Clutch release lever (4:R)
A lever for disengaging the variable transmission.
Enables the machine to be moved by hand without
the help of the engine. Two positions:
1. Lever out – transmission en-
gaged for normal operation.
There is an audible click when
the lever locks in the outer posi-
tion.
2. Lever in – transmission disen-
gaged. The machine can be
moved by hand.
The machine may not be towed over long distances
or at high speeds. The transmission could be dam-
aged.
54
ENGLISH
2.4.15 Seat (5:S)
The seat can be folded and adjusted for-
wards and backwards. The seat's forward/
backward position can be locked with the
knobs (5:T).
The seat is equipped with a safety switch that is
connected to the machine's safety system. This
means that certain activities that can entail danger
cannot be carried out when nobody is sitting in the
seat. See also 4.3.2.
2.4.16 Engine casing (6:U)
In order to access the fuel cock, battery
and engine, the machine has an engine
casing that can be opened. The engine cas-
ing is locked with a rubber strap.
The engine casing is opened as follows:
1. Undo the rubber strap (6:V) at the front edge of
the casing.
2. Carefully lift the engine casing back.
Close in the reverse order.
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
3 AREAS OF USE
The machine may only be used for the following
tasks using the genuine STIGA accessories stated.
Work
Mowing
Sweeping
Snow clearance
Grass clipping and
leaf collection
Grass and leaf
transport
Sand spreading
Weeding on gravel
paths
Lawn edge trim-
ming
Moss scarification Using moss scarifier.
Accessories, STIGA genuine
Using mowing decks:
107 M, 107 M HD, 107 M HD
El, 121 M, 121 M El, 125 Combi
Pro, 125 Combi Pro El and with
flail mower.
Using brush unit or collector
brush unit. The use of a dust
guard is recommended with the
first option.
Using snow blade or snow
thrower Snow chains and frame
weights are recommended.
Using towed collector 30" or
42".
Using dump cart Standard, Maxi
or Combi.
Using sand spreader. Can also
be used for spreading salt. Snow
chains and frame weights are
recommended.
Using front-mounted hoe.
Using edge trimmer.