Specifications; Specific Safety Rules - Makita HM1400 Betriebsanleitung

ENGLISH
1 Bolts
2 Grip
3 Notched portion
4 Tool retainer

SPECIFICATIONS

Model
Blows per minute ....................................................................................... 1,200
Overall length ............................................................................................ 613 mm
Net weight .................................................................................................. 17 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
be operated on single-phase AC/DC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to hammer safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal injury.
1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
4. Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
5. Be sure the bit is secured in place before opera-
tion.
6. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
7. In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
8. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
9. Hold the tool firmly with both hands.
Explanation of general view
5 Switch lever
6 Handle
7 Holder cap plate
8 Screwdriver
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
12. Do not point the tool at any one in the area when
13. Do not touch the bit or parts close to the bit
14. Do not operate the tool at no-load unnecessarily.
15. Some material contains chemicals which may be
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
GEB004-2
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing grip (Fig. 1)
Install the grip securely with the bolts using the hex
wrench.
Installing or removing bull point or other bits
(cold chisel, etc.) (Fig. 2 & 3)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Turn up the tool retainer. With the notched portion of the
bit facing the tool retainer, insert the bit into the tool bar-
rel as far as it will go.
Return the tool retainer to its original position to secure
the bit.
To remove the bit, follow the installation procedure in
reverse.
Switch action (Fig. 4)
CAUTION:
• Before plugging in the tool, always check to see that
the switch lever actuates properly and returns to the
"OFF" position when released.
• Do not tape, tie or otherwise secure the switch lever in
the "ON" position.
To start the tool, simply squeeze the switch lever.
Release the switch lever to stop.
9 Brush holder cap
10 Plate 50
11 Hammer grease
HM1400
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
HM1400K
1,200
600 mm
17 kg
3