Specifications; Ec Declaration Of Conformity; Specific Safety Rules - Makita HM1202 Bedienungsanleitung

ENGLISH
1-1. Switch lever
2-1. Adjusting dial
3-1. Power-ON indicator lamp (green)
3-2. Service indicator lamp (red)
4-1. Side handle
4-2. Clamp nut
5-1. Side handle base
5-2. Clamp nut
6-1. Bit grease

SPECIFICATIONS

Blows per minute
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for chiselling work in concrete, brick,
stone and asphalt as well as for driving and compacting
with appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.46 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
Model; HM1202, HM1202C
For European countries only
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 89/336/EEC, 98/37/EC.
Measured sound power level: 99 dB
Explanation of general view
6-2. Bit shank
7-1. Bit
7-2. Tool holder cover
9-1. Change ring
11-1. Commutator
11-2. Insulating tip
11-3. Carbon brush
12-1. Screwdriver
12-2. Rear cover
Model
Overall length
Net weight
Safety class
HM1202
1900 min
ENE045-1
Guaranteed sound power level: 101 dB
These sound
accordance with Council Directive, 2000/14/EC.
Conformity assessment procedure: Annex VI
Notified body: BSI Product Services, Maylands Avenue,
ENF002-1
Hemel Hempstead HP2 4SQ, England
Vibration
The typical weighted root mean square acceleration
value is 11 m/s
This value has been obtained according to EN60745.
ENF100-1
000087
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
ENH112-6
(gained from repeated use) replace strict adherence
to hammer safety rules. If you use this tool unsafely
or incorrectly, you can suffer serious personal
injury.
1. Wear ear protectors. Exposure to noise can
cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping
surfaces when performing an operation where
4
12-3. Screws
13-1. Screwdriver
13-2. Brush holder cap
14-1. Screws
15-1. Socket wrench
15-2. Crank cap
16-1. Hammer grease
HM1202C
-1
950 - 1,900 min
578 mm
9.3 kg
II
power levels were
2
.
Yasuhiko Kanzaki CE2006
Director
-1
measured in
GEB004-2