Vacuum Packing In Magic Vac; Vacuum Packing In Glass Jars; Vacuum Packing With Magic Vac Bottle Caps; Vacuum Packing With Cap Attachment - Magic Vac P0104ED Betriebsanleitung

WARNING: DO NOT LEAVE THE LID WITH LOCKS ENGAGED WHEN THE UNIT IS NOT IN USE.
vegetables. Their transparency and design makes
them attractive to display on kitchen shelves while
ensuring that their contents are clearly visible.
- Fill the container leaving at least 3 cm of room
between the contents and upper rim and position
the lid on the container. Lock the safety catches
(18) before starting the vacuum process.
- Connect the container lid to the air inlet (6) of the
appliance by means of the connection hose (15)
(fig. N / fig. O).
- Lock the lid (4) by pushing the LOCK buttons (7);
the machine will carry out a vacuum packing cycle
and turn off automatically on its completion.
- Remove the hose from the container lid.
- Once a vacuum is formed, the vacuum indicator (17
fig. N) of the container should be depressed and it
should remain depressed throughout storage of
the vacuum-packed food item. Should this indica-
tor return into a raised position, it means that there
is no longer a vacuum inside the container.
- Press the central button to open the containers
(16) (fig. N / fig. O).
8 Vacuum packing in glass jars sealed with metal
caps (Leifheit type)
Use the large-sized cap attachment to pack foods in
glass jars with a metal cap.
- Fill the container leaving at least 3 cm of room
between the contents and upper rim.
- Connect the cap attachment (19) to the air inlet (6)
of the appliance by means of the connection hose
(15). Place the cap attachment directly on the jar
with the metal cap only (21) and press down, mak-
ing sure it fits correctly (fig. P).
- Lock the lid (4) by pushing the LOCK buttons (7);
the machine will carry out a vacuum packing cycle
and turn off automatically on its completion. Make
sure that the cap attachment holds firmly by keep-
ing it pressed with your hand.
- Disconnect the hose from the cap attachment.
Remove the cap attachment from the jar.
- Apply the ring (22) supplied with the jar and screw
it down all the way (fig. P).
- To open a glass jar vacuum-sealed with a metal
cap, use the cap opener provided (the side with
writing should be turned up). Position the cap
opener as shown in figure Q and gently pry open
the cap until the vacuum is released. Remove the
metal cap. This accessory allows you to reuse the
cap.
9 Vacuum packing with MAGIC VAC
The MAGIC VAC Bottle Cap may be used to seal part-
®
ly filled bottles of wine or non-fizzy beverages. Using
the Bottle Cap will allow you to create a vacuum
inside the bottle so as to slow down oxidisation and
preserve the freshness and flavour of its contents for
a longer time.
- By means of the connection hose (15) connect the
air inlet (6) of the appliance to the MAGIC VAC
Bottle Cap (23) (fig. R). Press the Cap firmly into the
bottle.
OPERATING INSTRUCTIONS
bottle caps
®
®
19
- Lock the lid (4) by pushing the LOCK buttons (7);
the machine will carry out a vacuum packing cycle
and turn off automatically on its completion.
- Disconnect the hose from both the Bottle Cap and
the appliance immediately.
- To open a bottle sealed with the MAGIC VAC
Bottle Cap, simply pull the cap out of the bottle.
You will hear the air rushing into the bottle.
10 Vacuum packing with Cap Attachment in
MAGIC VAC Executive containers or in containers
®
sealed with MAGIC VAC
®
previous model of knob
To use the Cap Attachment in MAGIC VAC
containers or in containers sealed with MAGIC VAC
Universal Caps with the previous model of knob,
read the instructions supplied in our web page
www.flaemnuova.it
®
Universal Caps with the
Executive
®
®