Installation; Grss & Grssr Models; Grssb Models - Hatco GLO-RAY GRSS Serie Installations- Und Bedienungshandbuch

INSTALLATION

WARNING
For safe and proper operation, the unit must be located a
reasonable distance from combustible walls and
materials. If safe distances
discoloration or combustion could occur.
CAUTION
To avoid any injury or damage locate the unit at the proper
counter height, in an area that is convenient for use. The
location should be level to prevent the shelf or its contents
from accidentally falling, and strong enough to support
the weight of the unit and food.
WARNING
Do not lay unit on the side with the control panel or
damage to the unit could occur.
WARNING
To avoid any injury or damage to the unit do not pull unit
by power cord.
WARNING
To prevent any injury, discontinue use if power cord is
frayed or worn.
WARNING
If the power supply cord is damaged, it must be replaced
by Hatco, an Authorized Service Agent, or a person with
similar qualifications to avoid a hazard.
GRSS & GRSSR MODELS
1. Remove unit from box.
2. Remove information packet. To prevent delay in
obtaining warranty coverage, fill out and mail in the
warranty card to Hatco.
3. Remove tape and protective packaging from all surfaces of
unit.

GRSSB MODELS

CAUTION
To avoid any injury or damage do not operate the GRSSB
(Built-In Models) without the trim mounting ring and the
control box properly mounted per the installation
instructions.
NOTICE
Damage to non-metallic countertop material caused by
heat generated from Hatco equipment is not covered
under the Hatco warranty. Recommended for use in
metallic counters. For other surfaces, verify that the
material is suitable for temperature up to 93°C (200°F).
MODEL MINIMUM WIDTH
GRSSB-2418 622 mm (24-1/2")
GRSSB-3018 775 mm (30-1/2")
GRSSB-3618 927 mm (36-1/2")
GRSSB-4818 1232 mm (48-1/2")
GRSSB-6018 1537 mm (60-1/2")
GRSSB-7218 1842 mm (72-1/2")
Form No. GRSSCEM-1207
are not maintained,
COUNTERTOP CUTOUT (SEE 8 )
MAXIMUM WIDTH
629 mm (24-3/4")
781 mm (30-3/4")
933 mm (36-3/4")
1238 mm (48-3/4")
1543 mm (60-3/4")
1848 mm (72-3/4")
10
1. Remove unit from box.
2. Remove information packet. To prevent delay in
obtaining warranty coverage, fill out and mail in the
warranty card to Hatco.
3. Remove tape and protective packaging from all surfaces of
unit.
4. Prepare countertop
recommended countertop cutout dimensions.)
5. Apply a bead of NSF (National Sanitation Foundation)
approved sealant on the top edge of the countertop cutout
and the underside
See 8 .
6. Place the GRSSB unit into the countertop opening.
7. Remove any excess sealant.
8. Locate the remote control box assembly in an area that is
convenient for operation. If necessary, remove the end
brackets from the control box, rotate and reposition them.
The control box will require a hole mounting pattern of
194 mm x 32 mm (7-5/8" x 1-1/4"). See Figure 9 for
mounting distances.
NOTE: Remote control box should be mounted with 6 mm
(1/4") minimum diameter screw head utilizing the keyholes
located on the mounting brackets. Remote control box is to be
readily removable not permanently mounted.
9. Once all components
OPERATION section.
NOTE: A 1829 mm (6') cord is supplied with this appliance; any
excess cord should be neatly routed so it does not hang down.
MINIMUM DEPTH
470 mm (18-1/2")
470 mm (18-1/2")
470 mm (18-1/2")
470 mm (18-1/2")
470 mm (18-1/2")
470 mm (18-1/2")
opening. (See Figure 8
of the trim mounting
are secured, proceed
MAXIMUM DEPTH
476 mm (18-3/4")
476 mm (18-3/4")
476 mm (18-3/4")
476 mm (18-3/4")
476 mm (18-3/4")
476 mm (18-3/4")
for
ring.
to