Installation; General; Floor Sheet; Display Racks - Hatco FDW Serie Installations- Und Bedienungshandbuch

INSTALLATION

GENERAL

The Flav-R-Fresh Holding and Display Cabinets are shipped
with most components installed and ready for operation.
The following installation instructions must be performed before
plugging in and operating the cabinet.

FLOOR SHEET

The stainless steel floor in all Flav-R-Fresh units is protected during
shipping with a sheet of corrugated cardboard. This protection must
be removed prior to cabinet operation.

DISPLAY RACKS

The chrome-plated display racks have packing material
and cardboard attached for protection during shipping. This
protection must be removed prior to cabinet operation.

LEGS

The Flav-R-Fresh cabinets are shipped with four (4) 2.5 cm (1")
metal screw-type feet attached to the bottom of the unit. If you
ordered the cabinet with the optional 10 cm (4") Adjustable Legs,
see ACCESSORIES for installation instructions.

GLASS PANELS

The Flav-R-Fresh Holding and Display Cabinets have tempered
glass panels that are protected during shipping by rubber tabs along
the glass edges and taped to securely hold the panels. See 4 .
These tabs and tape must be removed prior to cabinet operation.
NOTE: If installing 10 cm (4") legs, do not remove glass protection
until leg installation is complete. See ACCESSORIES.
The unit must be transported in an upright position. If laid
on its side, all glass surfaces must be secured with tape,
and water must be drained from the unit.

REVERSIBLE ACCESS DOOR

The Flav-R-Fresh access door may be hinged on either the left
or right side for your convenience. See 5 . To reverse the door
hinge, follow these instructions:
1. Remove the top hinge pin screw holding door to hinge.
Also remove nylon washer.
2. Tip the door assembly toward you (away from cabinet)
and lift gently to clear the bottom hinge assembly. Remove
nylon washers.
3. Remove the screws holding hinges to the cabinet.
4. Remove screws from non-hinge side of the cabinet and insert
them in the other side, where the hinge screws were.
5. Mount hinges on the opposite side, using the original hinge
mounting screws. Do not tighten the screws.
6. Carefully rotate the door 180° and re-install the hinge pin screw
that was removed in Step 1.
7. Remove the hinge pin screw on the end that is now the top.
8. Carefully place the door assembly with the two (2) nylon
washers onto the bottom hinge.
9. Tip/tilt the door assembly towards the cabinet and align
the door top with the hinge. Re-install the other door hinge
pin with one (1) nylon washer.
10. With the door in place, tighten the hinge mounting screws,
making sure the door is level and in place.
Form No. FDWCEM-1002
Downloaded from www.Manualslib.com
CAUTION
manuals search engine

STRIKER PLATE REPLACEMENT

1. Carefully remove striker plate from bottom of door and clean
adhesive from the plate and door glass.
2. Position the striker plate on the top of the door, making sure
when the door is closed the striker plate locates squarely
against the magnet and mark the position.
3. Clean glass with a non-oily cleaner, such as isopropyl alcohol
(rubbing alcohol), and do not touch the surface.
4. Attach the striker plate to the glass door at the marked position
using a N.S.F. approved silicon type adhesive. Let the adhesive
dry before closing the door against the magnet.

LOCATION

CAUTION
Locate the Display Cabinet at the proper counter height,
in an area that is convenient for use. The location should
be level to prevent the cabinet or its contents from
accidentally falling.
WARNING
For safe and proper operation, the Display Cabinet must
be located a reasonable distance from combustible walls
and materials. If safe distances are not maintained,
discoloration or combustion could occur.
CAUTION
The unit must be transported in the upright position. If laid
on its side, all glass surfaces must be secured with tape,
and water must be drained from the unit.
7