Installation; Unpacking; Location; Reversible Access Door - Hatco FSD Series Installations- Und Bedienungshandbuch

INSTALLATION

UNPACKING (SEE 5 )
The Flav-R-Savor ® Holding and Display Cabinets are shipped
with most components installed and ready for operation. The
following installation instructions must be performed before
plugging in and operating the cabinet.
WARNING
Do not lay unit on the side with the control panel or
damage to the unit could occur.
WARNING
To prevent any injury or damage to the unit do not pull unit
by power cord.
1. Remove unit from box.
2. Remove information packet. To prevent delay in
obtaining warranty coverage, fill out and mail in the
warranty card.
3. Remove tape and protective film from all surfaces of unit.
4. The stainless steel floor in all Flav-R-Savor units is
protected during shipping with a sheet of corrugated
cardboard. This protection must be removed prior to
cabinet operation.
5. The plated display racks have packing material and
cardboard attached for protection during shipping. This
protection must be removed prior to cabinet operation.
6. The Flav-R-Savor Holding and Display Cabinets have
tempered glass panels that are protected and secured
during shipping by rubber tabs and/or foam tape along the
glass edges. These tabs and foam tape must be removed
prior to cabinet operation.
To remove a glass panel, grasp the panel firmly from inside
and outside of the cabinet, lift up and out of the bottom
channel, then carefully lower glass panel until it clears the
upper channel.
To reinstall, position glass panel top edge under the
cabinet lip, raise panel until it clears the bottom channel,
then carefully lower the panel until it rests in the bottom
channel.
7. If your unit was ordered with Merchandising Decal
Graphics, see ACCESSORIES for installation instructions.
If your unit is equipped with the optional Merchandising
Display Sign, see ACCESSORIES for installation
instructions.
If installing the optional Stacking Kit, see ACCESSORIES
for installation instructions.

LOCATION

WARNING
For safe and proper operation, the unit must be located a
reasonable distance from combustible walls and
materials. If safe distances
discoloration or combustion could occur.
CAUTION
To avoid any injury or damage locate the Holding Cabinet
at the proper counter height, in an area that is convenient
for use. The location should be level to prevent the unit or
its contents from accidentally falling, and strong enough
to support the weight of the unit and food.
CAUTION
The unit must be transported in an upright position. If laid
on its side, the water must be drained from the unit.
Form No. FSDCEM-0805
are not maintained,
12
CAUTION
The National Sanitation Foundation (NSF) requires that
units over 914 mm (36") in length or weighing more than
36 kg (80 lbs.) to be either sealed or raised on the
installation surface. If this unit cannot be sealed at the
point of use, 102 mm (4") legs are included to allow for
proper cleaning access below unit.
NOTE: The unit must be transported in the upright position. If
laid on its side, all glass surfaces must be secured with tape,
and water must be drained from the unit. See DRAINING THE
RESERVOIR in the MAINTENANCE section.
REVERSIBLE ACCESS DOOR (SEE 6 )
1. Remove hinge pivot pin from top of door left side and
carefully remove door from hinges. Do not lose plastic
washer located under bottom hinge pin.
2. Swap the door hinges with the strike plates on the right side
using original hardware.
3. Reinstall hinge pivot
step 1.
4. Rotate the door 180° and remove other hinge pin.
5. Place plastic washer on bottom hinge pin and install door
into hinges. Install top hinge pivot pin and tighten securely.
NOTE: See RELOCATING PROXIMITY SWITCH when
reversing a door.

RELOCATING PROXIMITY SWITCH

(Rotating Rack Models Only—FSD-1, FSDT-1,
FSD-2, FSDT-2) (See 7 )
FSD Models equipped with rotating rack will require relocating
the proximity switch(es) when reversing the door(s).
The proximity switch stops the rack from rotating when the
door is opened. Follow these steps listed so the proximity
switch is in the proper position after reversing the door(s). Unit
requires one switch per door.
1. Remove the 4 screws and top cover.
2. Remove the screw and nut securing the proximity switch to
the cabinet. The screw is accessed from inside the cabinet.
Reinstall screw and nut into hole after removing switch.
3. Cut the cable tie securing the proximity switch wires to the
wiring harness. Mark the two wires for reassembly and
unplug the wires from the proximity switch. Route the wires
to the opposite corner and reattach the wires to the switch.
4. Remove the screw and nut from the new mounting hole.
Using opposite hole on switch, secure the proximity switch
to the mounting hole with the screw and nut.
Make sure to maintain switch orientation when tightening
hardware.
5. Make sure wires do not interfere with other components
inside the cabinet then secure switch wires to wiring
harness with a cable tie (not supplied).
NOTE: On models equipped with two doors, it may be
necessary to move the air chamber to access the proximity
switch on the customer side door. Drain all water from the unit,
remove the drain plug from inside the cabinet, and remove four
screws securing air chamber assembly to the cabinet.
Carefully move air chamber out of the way to access proximity
switch. Reassemble after relocating switch.
6. Install cover and four screws.
pin to door removed in