Werbung
Verfügbare Sprachen
Verfügbare Sprachen
WARNING
For safe and proper operation plug unit into a properly
grounded electrical outlet of the correct voltage, size and
plug configuration. If the plug and receptacle do not
match, contact a qualified electrician to determine the
proper voltage and size and install the proper electrical
outlet.
WARNING
The Glo-Ray Heated Stone Shelf is not waterproof. To
avoid any injury or damage to the unit DO NOT submerge
or saturate with water. Do not operate if it has been
submerged or saturated with water.
CAUTION
Some exterior surfaces on the unit will get hot. Use
caution when touching these areas to avoid injury.
CAUTION
Unit is not weatherproof. For safe and proper operation
locate the unit indoors where the ambient air temperature
is a minimum of 21°C (70°F).
GENERAL
The Hatco Glo-Ray
®
Heated Stone Shelves are designed for
maximum durability and performance, with minimum
maintenance.
WARNING
To avoid any injury or damage to the unit turn the power
switch OFF, unplug the unit and allow to cool before
performing any maintenance or cleaning.
CLEANING
General
To preserve the finish of the Glo-Ray Heated Stone Shelf, it is
recommended that the surfaces be wiped daily with a damp
cloth.
WARNING
The Glo-Ray Heated Stone Shelf is not waterproof. To
avoid any injury or damage to the unit DO NOT submerge
or saturate with water. Do not operate if it has been
submerged or saturated with water.
WARNING
This appliance is not jet-proof construction. To assure
safe and proper operation do not use jet-clean-spray to
clean this appliance.
CLEANING FOR SWANSTONE
SURFACE
Use of the following products will not damage the Swanstone
Solid Surface. Follow the directions on the product labels. If
these methods fail to produce acceptable results, contact the
Swanstone representative in your area.
Hard to Remove Stains
For hard to remove stains, abrasive cleaners recommended
include Ajax, Comet, Bon Ami, or Bar Keeper's Friend. Also,
the use of an abrasive pad such as "Scotch-Brite." Abrasive
pads available from Hatco, part number 04.39.049.00.
NOTE: Do not use steel wool or metal scouring pads.
®
SOLID
®
11
1. Plug warmer into a properly grounded electrical outlet of
the correct voltage, size and plug configuration. See
SPECIFICATIONS for details.
2. Place
the
Power
Switch
(See 10 )
3. Turn the thermostat to the desired temperature setting.
4. Allow unit 30 minutes to reach operating temperature.
NOTE: See ACCESSORIES for installation and operation
information for GRSSB Series units with flush mount control
box.
NOTE: See ACCESSORIES for installation and operation
information for GRSSB Series units with flush mount electronic
Indicating Temperature Control (ITC).
Mineral Based Stains
For a mineral based stain, cleaners designed to remove iron or
rust is recommended and should not harm Swanstone
Scratches
For scratches use sandpaper starting with coarsest grit and
going to finest grit until scratch disappears. Blend area in with
abrasive finishing pad.
WARNING
If service is required on this unit, contact your Authorized
Hatco Service Agent, or contact the Hatco Service
Department at 414-671-6350 International fax 414-671-
3976.
WARNING
This product has no "user" serviceable parts. To avoid
damage to the unit or injury to personnel, use only
Authorized Hatco Service Agents and Genuine Hatco
Replacement Parts when service is required.
WARNING
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
aftermarket or generic replacement parts do not have the
characteristics that will allow them to operate safely in
Hatco equipment. It is essential to use Hatco Replacement
Parts when repairing Hatco equipment. Failure to use
Hatco Replacement Parts may subject operators of the
equipment to hazardous electrical voltage, resulting in
electrical shock or burn.
OPERATION
in
the
ON
position.
MAINTENANCE
®
.
Form No. GRSSCEM-1207
Werbung
Kapitel
Fehlerbehebung
